The details are as follows :----
This details will help you.
Thanks.
See below latest solved car problems :----
How to remove Intake Manifold Tuning Valve?
http://technoanswers.blogspot.com/2012/01/how-to-remove-intake-manifold-tuning.html
CMFI details for GMC vehicles?
http://technoanswers.blogspot.com/2012/01/cmfi-details-for-gmc-vehicles.html
Mazda MPV cranks but will not start?
MAZDA MPV WILL CRANK BUT NOT TURN OVER TO START?
http://technoanswers.blogspot.com/2012/01/mazda-mpv-will-crank-but-not-turn-over.html
Freightliner fl112 fuse box diagram?
http://technoanswers.blogspot.com/2012/01/freightliner-fl112-fuse-box-diagram.html
Car will not turn the ignition to start?
http://technoanswers.blogspot.com/2012/01/car-will-not-turn-ignition-to-start.html
Car only starts when gas pedal is pressed?
http://technoanswers.blogspot.com/2012/01/car-only-starts-when-gas-pedal-is.html
Hyundai coupe f2 hazard fault?
http://schematicsdiagram.blogspot.com/2012/01/hyundai-coupe-f2-hazard-fault.html
Where is the bulb located in glove box?
http://repairhelpcenter.blogspot.com/2012/01/where-is-bulb-located-in-glove-box.html
Additional wiring harness needs to be installed in a brake controller for electric brakes on 2012
http://repairhelpcenter.blogspot.com/2012/01/additional-wiring-harness-needs-to-be.html
Fail smog test due to gas filter hose?
http://repairhelpcenter.blogspot.com/2012/01/fail-smog-test-due-to-gas-filter-hose.html
Clutch squeaking under hood?
http://repairhelpcenter.blogspot.com/2012/01/clutch-squeaking-under-hood.html
Replace door stay assemblies on
http://repairhelpcenter.blogspot.com/2012/01/replace-door-stay-assemblies-on-toyota.html
Acceleration lag problem?
http://repairhelpcenter.blogspot.com/2012/01/acceleration-lag-problem.html
How to Replace rear quarter glass on
http://repairhelpcenter.blogspot.com/2012/01/how-to-replace-rear-quarter-glass-on.html
Overdrive light in the dash blinks?
http://repairhelpcenter.blogspot.com/2012/01/overdrive-light-in-dash-blinks.html
How to bypass immobiliser on Rover 200?
http://technoanswers.blogspot.com/2012/01/how-to-bypass-immobiliser-on-rover-200.html
Hood clear coat peeling off?
http://repairhelpcenter.blogspot.com/2012/01/hood-clear-coat-peeling-off.html
Engine stumbles coming off idle when warm?
http://repairhelpcenter.blogspot.com/2012/01/engine-stumbles-coming-off-idle-when.html
How to Refit Rear seat on Rover 600?
http://repairhelpcenter.blogspot.com/2012/01/how-to-refit-rear-seat-on-rover-600.html
How to replace the speakers on 2011 Ford Edge?
http://technoanswers.blogspot.com/2012/01/how-to-replace-speakers-on-2011-ford.html
How to Remove Rear seat on Rover 600?
http://repairhelpcenter.blogspot.com/2012/01/there-are-3-10mm-bolts-at-back-of-seats.html
http://technoanswers.blogspot.com/2012/01/toyota-solara-rattling-in-rear.html
Removal & Installation
WARNING
Any brake fluid that is removed from the system should be discarded. Never reuse brake fluid. Do not allow any brake fluid to come in contact with a painted surface; it will damage the paint.
- Disconnect the negative battery cable.
- Place a cloth under the master cylinder to prevent brake fluid from falling on painted surfaces.
- At the proportioning valve, disconnect the brake lines from the master cylinder using a line wrench.
- Remove the rear wheel brake line from the right side of the ABS solenoids using a line wrench.
- Remove the front wheel brake line from the lower left port of the proportioning valve using a line wrench.
- Disconnect the wiring harness connector to ABS solenoids.
- Disconnect the wiring harness connector to proportioning valve.
- Remove the master cylinder mounting nuts.
- Remove bracket with the ABS solenoids and proportioning valve attached.
- Disconnect the proportioning valve from the ABS solenoid bracket.
To install:
- Attach the proportioning valve and the ABS solenoids to the bracket.
- Place bracket assembly on vacuum booster studs and install nuts. Tighten nuts to 115 inch lbs. (13 Nm).
NOTETo lessen the possibility of damaging the brake line nut threads, loosen the nut at the opposite end of the brake line. This will provide greater flexibility for a proper thread start. Once both ends are properly started, tighten the nuts to specification. - Attach rear wheel brake line to right side port of ABS solenoid and tighten the nut to 13 ft. lbs. (18 Nm).
- Attach front wheel brake line to lower left port of proportioning valve and tighten the nut to 13 ft. lbs. (18 Nm).
- Attach brake lines to master cylinder and tighten the nut to 13 ft. lbs. (18 Nm).
- Connect ABS solenoid and proportioning valve wire harness connectors.
- Refill the master cylinder reservoir.
- Connect the negative battery cable.
- Bleed brake system and check for fluid leakage.
This details will help you.
Thanks.
See below latest solved car problems :----