@

@

Tuesday, January 31, 2012

Problem with cam synchronizer on 1996 Ford Taurus

If Cam Synchronizer fails,then it has to be replaced.

While replacing,
Just mark the old one an put the new one in in the same spot. In this procedure no need to use the alignment tool, and  put the engine on tdc. After installing start the engine and check,does it  starts right up and seems to run good.
The idle is around 900rpm.If it seems just a bit high. Then it could the synchro not being in the exact spot cause this.

In most cases these method  works just fine as long as you didnt move the engine. In most cases if the synchronizer was installed wrong you would have a check engine light and the engine would not run correctely. If you have no running issues your are likely fine. The idle speed should not have been effected and if it was the idle would likely roll up and down. I would start with making sure someone hasn't screwed the throttle hard stop in a bit and if so back it out a bit to be sure the throttle dosnt stick and it should be fine.

This details will help.
Thanks.


see below latest solved car problem:----

2004 ford freestar van idles rough?

       

http://howtobyme.blogspot.in/2012/01/2004-ford-freestar-van-idles-rough.html

How to remove Intake Manifold Tuning Valve?

http://technoanswers.blogspot.com/2012/01/how-to-remove-intake-manifold-tuning.html

CMFI details for GMC vehicles?

http://technoanswers.blogspot.com/2012/01/cmfi-details-for-gmc-vehicles.html

Mazda MPV cranks but will not start?

http://technoanswers.blogspot.com/2012/01/mazda-mpv-cranks-but-will-not-start.html

MAZDA MPV WILL CRANK BUT NOT TURN OVER TO START?

http://technoanswers.blogspot.com/2012/01/mazda-mpv-will-crank-but-not-turn-over.html

Freightliner fl112 fuse box diagram?

http://technoanswers.blogspot.com/2012/01/freightliner-fl112-fuse-box-diagram.html

Car will not turn the ignition to start?

http://technoanswers.blogspot.com/2012/01/car-will-not-turn-ignition-to-start.html

Car only starts when gas pedal is pressed?

http://technoanswers.blogspot.com/2012/01/car-only-starts-when-gas-pedal-is.html

Hyundai coupe f2 hazard fault?

http://schematicsdiagram.blogspot.com/2012/01/hyundai-coupe-f2-hazard-fault.html

Where is the bulb located in glove box?

http://repairhelpcenter.blogspot.com/2012/01/where-is-bulb-located-in-glove-box.html

Additional wiring harness needs to be installed in a brake controller for electric brakes on 2012 Toyota Highlander?

http://repairhelpcenter.blogspot.com/2012/01/additional-wiring-harness-needs-to-be.html

Fail smog test due to gas filter hose?

http://repairhelpcenter.blogspot.com/2012/01/fail-smog-test-due-to-gas-filter-hose.html

Clutch squeaking under hood?

http://repairhelpcenter.blogspot.com/2012/01/clutch-squeaking-under-hood.html

Engine stalls when gas is given?

http://technoanswers.blogspot.in/2012/01/engine-stalls-when-gas-is-given.html

Replace door stay assemblies on Toyota?

http://repairhelpcenter.blogspot.com/2012/01/replace-door-stay-assemblies-on-toyota.html

Acceleration lag problem?

http://repairhelpcenter.blogspot.com/2012/01/acceleration-lag-problem.html

How to Replace rear quarter glass on Toyota Tacoma?

http://repairhelpcenter.blogspot.com/2012/01/how-to-replace-rear-quarter-glass-on.html

Overdrive light in the dash blinks?

http://repairhelpcenter.blogspot.com/2012/01/overdrive-light-in-dash-blinks.html

No pulse to injectors?

http://technoanswers.blogspot.com/2012/01/no-pulse-to-injectors.html

How to bypass immobiliser on Rover 200?

http://technoanswers.blogspot.com/2012/01/how-to-bypass-immobiliser-on-rover-200.html

HVAC Control panel has no power on 2000 lincoln navigator?

http://technoanswers.blogspot.in/2012/01/hvac-control-panel-has-no-power-on-2000.html g� ~ d c ș� ��� ial; background-color: white; background-position: initial initial; background-repeat: initial initial; ">ABS light comes on and Car makes Grinding noise?

http://repairhelpcenter.blogspot.com/2012/01/abs-light-comes-on-and-car-makes.html

Squealing at start up on car?

http://technoanswers.blogspot.com/2012/01/squealing-at-start-up-on-car.html


Labels: ford synchronizer installation, high idle after installing cam synchronizer, how to install cam synchronizer on Ford, Problem with cam synchronizer on 1996 Ford Taurus

Chirping sound coming from engine?

The noise is high pitched and vehicle is ford taurus.
In most cases the noise you are discribing is cuased by a failing camshaft position sensor synchronizer which is the drive gear for the camshaft position sensor . Its located right next to the thermostat housing on the intake and in most cases it will require replacing to resolve the noise.

The drive gear runs about $156 and the cam sensor run about $36.00 so about $180 in parts and about 1.5 hours in labor will resolve this.

This details will help.
Thanks.

See below latest solved car problems:---

Heater makes clicking noise under dash on Ford Explorer?

http://technoanswers.blogspot.in/2012/01/heater-makes-clicking-noise-under-dash.html

Clicking noise under dash and front defroster not working?

http://technoanswers.blogspot.com/2012/01/clicking-noise-under-dash-and-front.html




Car makes clicking noise?

http://howtobyme.blogspot.com/2011/11/car-makes-clicking-noise.html

Car makes whining noise like driving on rough pavement?

http://howtobyme.blogspot.com/2011/12/car-makes-whining-noise-like-driving-on.html

Chirping Noise From Car?

http://technoanswers.blogspot.com/2011/11/chirping-noise-from-car.html
                     

What are the possibilities for Clicking noise in car?

http://technoanswers.blogspot.com/2011/11/what-are-possibilities-for-clicking.html

Engine makes noise and Cooling Fan belt Breaks?

http://howtobyme.blogspot.com/2011/12/engine-makes-noise-and-cooling-fan-belt.html

Vehicle Makes Clicking Sound While Taking turns?

http://schematicsdiagram.blogspot.com/2011/12/vehicle-makes-clicking-sound-while.html

ABS light comes on and Car makes Grinding noise?

http://repairhelpcenter.blogspot.com/2012/01/abs-light-comes-on-and-car-makes.html

Squealing at start up on car?

http://technoanswers.blogspot.com/2012/01/squealing-at-start-up-on-car.html


Labels: ford taurus engine makes chirping noise, high pitched chirping noise, noise coming from engine on ford

Keyfob remote not working on 2003 Ford E350 Econoline?

In this case,the first thing to be checked is TRANSCEIVER FUSE.This fuses controls the Keyfob working communication on car.

There are 4 fuses you need to check in the interior fuse panel, they are the F2-35, the F2-3, the F2-32 and the F2-4 fuses. In addition also  check F2-5.

If all fuse check ok try reprogramming the FOB once again with the enclosed factory instructions.

The instructions are as follows :----
General Procedures for programing Ford keyless remotes.
NOTE: All remote keyless entry (RKE) transmitters must be programmed at the same time.
NOTE: Programming of the RKE transmitters can be accomplished using a scan tool or by carrying
out the following steps:
1. The vehicle must be electronically unlocked before entering program mode using the RKE
transmitter, keyless entry keypad (if equipped) or door lock control switch while the driver door
is open.
2. Turn the key from OFF to RUN 8 times within 10 seconds, with the eighth turn ending in RUN.
If the module successfully enters the program mode, it locks and then unlocks all doors.
3. Within 210 seconds, press any button on an RKE transmitter, and the doors lock and then
unload to confirm that each RKE transmitter is programed. Repeat this step for each RKE
transmitter.
4. If the door locks do not respond for any RKE transmitter, wait several seconds and press the
button again. If the door locks still fail to respond, refer to Inspection and Verification in this
section. Make sure that no more than the maximum number (4) of RKE transmitters are
attempting to be programmed.
5. Exiting the programming mode is accomplished if one of the following occurs:
The key transitions to the OFF position.
Twenty seconds have passed since entering programming mode or since the last RKE 
transmitter was programmed.
The maximum number (4) of RKE transmitters have been programmed.

But if this detailed instructions are not helping and all the mentioned fuses are checked absolutely ok.
Then its a faulty Keyfob remote.It has to be replaced.

This details will help.
Thanks.

See below latest solved car problems :----

Ford Keyless Remote Fob Reprogramming?

http://schematicsdiagram.blogspot.com/2011/12/ford-keyless-remote-fob-reprogramming.html

After getting car washed, check engine light is ON and key less entry not working, tried reprogramming. Also car shows fuel pressure?

http://schematicsdiagram.blogspot.com/2011/12/after-getting-car-washedcheck-engine.html

VSC light comes on and zero calibration?

http://technoanswers.blogspot.com/2012/01/vsc-light-comes-on-and-zero-calibration.html

Can car radio code block Passkey anti theft system ?

http://schematicsdiagram.blogspot.com/2011/12/can-car-radio-code-block-passkey-anti.html

Audi A8 Key Fob Programming?

http://technoanswers.blogspot.com/2011/12/audi-a8-key-fob-programming.html

Oldsmobile Aurora Key Fob Reprogramming?

http://technoanswers.blogspot.com/2011/12/olds-aurora-key-fob-reprogramming.html

Buick Lesabre Key Fob Reprogramming?

http://technoanswers.blogspot.com/2011/12/buick-lesabre-key-fob-reprogramming.html
Labels: ford keyfob not working, key fob remote not working, reprogramming keyfob remote for ford, TRANSCEIVER FUSE for ford e350

Fuel pump has no power on 2002 ford 350 7.3 diesel?

This was noticed on many other ford models too.
The fuel pump will not get power,but if direct wire run from battery to fuel pump,then fuel pump with start and run.
This clearly indicates,that fuel pump is not faulty,but something is causing  no power issue on fuel pump.

Check for power at Inertia switch.
Try this check for power at the inertia switch after the key is turned on. If you have power at inertia switch,then run a positive wire from battery to the pink wire on the fuel pump and see if the pump runs fine and the truck starts or not.

If this is the case,in your problem,then read as follows :----

The power to the inertia switch come from the fuel pump relay on the Dark/green power wire at the Inertia switch and goes through the switch and out on the Pink/black wire directely to the pump. You need power in and out of the inertia switch while cranking. 

If you have power in and out and none at the Pump then you have a broken wire from the switch to the pump.

See the enclosed diagram shown below for better understanding :--------

graphic

Now if you have cranking voltage both in and out of the inertia switch .Then the problem is wire between inertia switch and fuel pump.That wire has to be replaced.
If so then simply overlay a new wire and you should be fine, its much easier than stripping the harness back to find the break. Just be sure to solider the connections on the new wire.

This details will help.
Thanks.

See the latest solved car problems :-----
For more Fuel/gasoline related help, follow the list mentioned below: -----

How to relieve fuel pressure?

http://technoanswers.blogspot.com/2012/01/how-to-relieve-fuel-pressure.html

Refueling problem?

http://repairhelpcenter.blogspot.com/2012/01/refueling-problem.html

Toyota Tercel consuming more fuel?

http://repairhelpcenter.blogspot.com/2012/01/toyota-tercel-consuming-more-fuel.html

How to maximize fuel economy on your vehicle?

http://schematicsdiagram.blogspot.com/2011/11/how-to-maximize-fuel-economy-on-your.html

Fuel pump relay and cooling fan relay troubleshooting on 1997 ford thunderbird?

http://repairhelpcenter.blogspot.com/2011/10/fuel-pump-relay-and-cooling-fan-relay.html

How to Increase gas mileage on 2011 2500HD Duramax 6.6?

http://schematicsdiagram.blogspot.com/2011/12/how-to-increase-gas-mileage-on-2011.html

How to Test and Replace Fuel Injectors on Acura Car Models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-test-and-replace-fuel-injectors.html

How to replace Fuel Tank Assembly?

http://vwrepairhelp.blogspot.com/2011/11/how-to-replace-fuel-tank-assembly.html

FUEL LINES AND FITTINGS on Acura Car Models?

http://repairhelpcenter.blogspot.com/2011/11/fuel-lines-and-fittings-on-acura-car.html

Replacing Fuel Charging Assembly on Car?

http://vwrepairhelp.blogspot.com/2011/11/replacing-fuel-charging-assembly-on-car.html
                          

How to replace Fuel Pressure Regulator on Acura Car models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-fuel-pressure-regulator.html

How to test Fuel Pressure and replace Fuel Pump on Acura Car models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-test-fuel-pressure-and-replace.html

Car will not take fuel into the fuel tank?

http://repairhelpcenter.blogspot.com/2012/01/car-will-not-take-fuel-into-fuel-tank.html

PGM-FI Main Relay on Acura Car models?

http://repairhelpcenter.blogspot.com/2011/11/pgm-fi-main-relay-on-acura-car-models.html

How to Relieve Fuel System Pressure on Acura Car Models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-relieve-fuel-system-pressure-on.html

How to Replace a Fuel Injector
http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-fuel-injector.html

How to Replace a Fuel Pressure Regulator?
http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-fuel-pressure-regulator.html

How to Replace a Fuel Pump?
http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-fuel-pump.html

HOW TO CLEAN A FUEL SYSTEM

http://schematicsdiagram.blogspot.com/2011/07/how-to-clean-fuel-system.html

HOW TO REPLACE A FUEL TANK

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-fuel-tank.html

 

HOW TO REPLACE A FUEL TANK CAP

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-fuel-tank-cap.html

HOW TO REPLACE A FUEL PUMP ASSEMBLY

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-fuel-pump-assembly.html

Time to replace Fuel pump on 1998 Ford Explorer?

http://schematicsdiagram.blogspot.com/2011/12/time-to-replace-fuel-pump-on-1998-ford.html

Emergency fuel shut switch on Ford car?

http://schematicsdiagram.blogspot.com/2011/12/emergency-fuel-shut-switch-on-ford-car.html

How to jump fuel pump On Chevrolet Silverado 1500?

http://schematicsdiagram.blogspot.com/2011/12/how-to-jump-fuel-pump-on-chevrolet.html

Car won’t start when cold?

http://schematicsdiagram.blogspot.com/2011/12/car-wont-start-when-cold.html

Car won't start after sitting overnight?

http://schematicsdiagram.blogspot.com/2011/12/car-wont-start-after-sitting-overnight.html

Car loses power while acceleration?

http://schematicsdiagram.blogspot.com/2011/12/car-loses-power-while-acceleration.html

Fuel leaks from fuel pulsation dampener on Toyota Corolla?

http://repairhelpcenter.blogspot.com/2012/01/fuel-leaks-from-fuel-pulsation-dampener.html

Car will not allow to put fuel?

http://repairhelpcenter.blogspot.com/2012/01/car-will-not-allow-to-put-fuel.html

Adding performance chip to increase Fuel mileage MPG?

http://technoanswers.blogspot.com/2012/01/adding-performance-chip-to-increase.html

How to test Electric fuel pump on GMC sonoma?

http://technoanswers.blogspot.com/2012/01/how-to-test-electric-fuel-pump-on-gmc.html

Fuel gauge drops to Empty?

http://technoanswers.blogspot.com/2012/01/fuel-gauge-drops-to-empty.html

Fuel pump not working on 1991 Ford Ranger?

http://technoanswers.blogspot.in/2012/01/fuel-pump-not-working-on-1991-ford.html


Labels: ford 350 fuel pump wire is broken, fuel pump issues, fuel pump wiring diagram for ford 350 diesel engine, no power to fuel pump on ford 350

Car stalls when MAF sensor is connected?

Many car models notice this problems.The Engine stalls with MAF sensor plugged in,but when MAF is unplugged,the engine runs smooth with check engine light on dash.

The problem you are discribing in most likely faulty MAFs.But if MAF is replaced with new and still same problem noticed,then  defect is most likely due to a failed PCM (computer) or the connection to it from the MAF to the PCM. That being said, in most cases when the engine runs ok with the MAF unplugged it normaly means the MAF is Bad.

This details will help.
Thanks.

See below latest solved car problems :---

HVAC Control panel has no power on 2000 lincoln navigator?

http://technoanswers.blogspot.in/2012/01/hvac-control-panel-has-no-power-on-2000.html

Hood clear coat peeling off?

http://repairhelpcenter.blogspot.com/2012/01/hood-clear-coat-peeling-off.html

Engine stumbles coming off idle when warm?

http://repairhelpcenter.blogspot.com/2012/01/engine-stumbles-coming-off-idle-when.html

How to Refit Rear seat on Rover 600?

http://repairhelpcenter.blogspot.com/2012/01/how-to-refit-rear-seat-on-rover-600.html

How to replace the speakers on 2011 Ford Edge?

http://technoanswers.blogspot.com/2012/01/how-to-replace-speakers-on-2011-ford.html

How to Remove Rear seat on Rover 600?

http://repairhelpcenter.blogspot.com/2012/01/there-are-3-10mm-bolts-at-back-of-seats.html

Toyota solara rattling in rear?

http://technoanswers.blogspot.com/2012/01/toyota-solara-rattling-in-rear.html

Parking light stay on constantly?

http://repairhelpcenter.blogspot.com/2012/01/parking-light-stay-on-constantly.html

Engine hard to start after gas refill?

http://repairhelpcenter.blogspot.com/2012/01/engine-hard-to-start-after-gas-refill.html

Fuel pressure and spark is good but ford escort will not start?

http://technoanswers.blogspot.in/2012/01/fuel-pressure-and-spark-is-good-but.html

How to replace wheel bearing on Honda Civic?

http://repairhelpcenter.blogspot.com/2012/01/how-to-replace-wheel-bearing-on-honda.html


Labels: car runs fine with mass air flow sensor unplugged, car stalls, car stalls with maf connected

HVAC Control panel has no power on 2000 lincoln navigator?

Heat and AC control panel has no power on Lincoln navigator.'
In this cases the first thing to be checked is fuse.

The Control panel is powered up by the #2 fuse and the #22 fuse in the interior fuse panel and if they check ok then you need to remove the controller and check to see if you have key on voltage at the white/violet wire and the red/white power wires at the connector on the controller. If you do and the controller is still blank then it has likely failed.

See below the diagram for more understanding:-----

graphic


This details will help.
Thanks.

See below the latest solved car problems :----

Honda Odyssey Control panel removal?

http://howtobyme.blogspot.com/2011/12/honda-odyssey-control-panel-removal.html


How to replace control panel on Audi A4 models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-control-panel-on-audi-a4.html


2004 ford freestar van idles rough?


http://howtobyme.blogspot.in/2012/01/2004-ford-freestar-van-idles-rough.html

How to remove Intake Manifold Tuning Valve?

http://technoanswers.blogspot.com/2012/01/how-to-remove-intake-manifold-tuning.html

CMFI details for GMC vehicles?

http://technoanswers.blogspot.com/2012/01/cmfi-details-for-gmc-vehicles.html

Mazda MPV cranks but will not start?

http://technoanswers.blogspot.com/2012/01/mazda-mpv-cranks-but-will-not-start.html

MAZDA MPV WILL CRANK BUT NOT TURN OVER TO START?

http://technoanswers.blogspot.com/2012/01/mazda-mpv-will-crank-but-not-turn-over.html

Freightliner fl112 fuse box diagram?

http://technoanswers.blogspot.com/2012/01/freightliner-fl112-fuse-box-diagram.html

Car will not turn the ignition to start?

http://technoanswers.blogspot.com/2012/01/car-will-not-turn-ignition-to-start.html

Car only starts when gas pedal is pressed?

http://technoanswers.blogspot.com/2012/01/car-only-starts-when-gas-pedal-is.html

Hyundai coupe f2 hazard fault?

http://schematicsdiagram.blogspot.com/2012/01/hyundai-coupe-f2-hazard-fault.html

Where is the bulb located in glove box?

http://repairhelpcenter.blogspot.com/2012/01/where-is-bulb-located-in-glove-box.html

Additional wiring harness needs to be installed in a brake controller for electric brakes on 2012 Toyota Highlander?

http://repairhelpcenter.blogspot.com/2012/01/additional-wiring-harness-needs-to-be.html

Fail smog test due to gas filter hose?

http://repairhelpcenter.blogspot.com/2012/01/fail-smog-test-due-to-gas-filter-hose.html

Clutch squeaking under hood?

http://repairhelpcenter.blogspot.com/2012/01/clutch-squeaking-under-hood.html

Engine stalls when gas is given?

http://technoanswers.blogspot.in/2012/01/engine-stalls-when-gas-is-given.html

Replace door stay assemblies on Toyota?

http://repairhelpcenter.blogspot.com/2012/01/replace-door-stay-assemblies-on-toyota.html

Acceleration lag problem?

http://repairhelpcenter.blogspot.com/2012/01/acceleration-lag-problem.html

How to Replace rear quarter glass on Toyota Tacoma?

http://repairhelpcenter.blogspot.com/2012/01/how-to-replace-rear-quarter-glass-on.html

Overdrive light in the dash blinks?

http://repairhelpcenter.blogspot.com/2012/01/overdrive-light-in-dash-blinks.html

No pulse to injectors?

http://technoanswers.blogspot.com/2012/01/no-pulse-to-injectors.html

How to bypass immobiliser on Rover 200?

http://technoanswers.blogspot.com/2012/01/how-to-bypass-immobiliser-on-rover-200.html � a g �Ȼ � � 0pt;margin-right:0in;margin-bottom:0in;margin-left: 0in;margin-bottom:.0001pt;background:white'>http://howtobyme.blogspot.com/2011/12/how-to-remove-passenger-side-blend-door.html

How to Remove Driver side Blend Door Actuator on 2008 Honda Odyssey?


http://howtobyme.blogspot.com/2011/12/how-to-remove-driver-side-blend-door.html

Blower motor Resistor shorting problem?

http://schematicsdiagram.blogspot.com/2011/12/blower-motor-resistor-shorting-problem.html

Heat blows cold on drivers side and hot on passenger side?

http://schematicsdiagram.blogspot.com/2011/12/heat-blows-cold-on-drivers-side-and-hot.html

Hot air on the driver’s side vents only?

http://repairhelpcenter.blogspot.com/2012/01/hot-air-on-drivers-side-vents-only.html

Ford F150 Ac only blows through defrost vents?

http://technoanswers.blogspot.com/2012/01/forf-f150-ac-only-blows-through-defrost.html

Dodge A/C come out of defrost vents only?

http://technoanswers.blogspot.com/2012/01/dodge-ac-come-out-of-defrost-vents-only.html

Ac vacuum line on dodge cummins?

http://technoanswers.blogspot.com/2012/01/ac-vacuum-line-on-dodge-cummins.html

Ford ranger AC blows cold through defrost vents instead on cabin vents?

http://technoanswers.blogspot.com/2012/01/ford-ranger-ac-blows-cold-through.html

AC air blows through defrost vent only on Ford F-350 6.0 Diesel Engine?

http://technoanswers.blogspot.com/2012/01/ac-air-blows-through-defrost-vent-only.html

Ford Escape Air flow selector not working and Air blows from defrost vent only?

http://technoanswers.blogspot.com/2012/01/ford-escape-air-flow-selector-not.html

AC blows air out of defroster and floor vents only on ford excursion?

http://technoanswers.blogspot.in/2012/01/ac-blows-air-out-of-defroster-and-floor.html

Clicking noise under dash and front defroster not working?

http://technoanswers.blogspot.com/2012/01/clicking-noise-under-dash-and-front.html

Labels: heat and ac control panel has no power, HVAC Control panel has no power on 2000 lincoln navigator, no power on Lincoln ac and heat control panel

Fuel pressure and spark is good but ford escort will not start?

Reverse issue.In most of no start problem on car,the fuel pressure is low or spark is the issue.But in this case both major possibility the fuel pressure and spark is good.

The other common possibility on such problem is check engine light on dash.Is there check engine light steady on dash or not.
If yes,then there is definitely error code stored in car computer.The car ECM needs scanning to retrieve error codes.

But in case if there is no check engine light coming on dash,or if there is no error codes stored in cars ECM computer.Then in that case, further troubleshooting is required to confirm the problem.

If you are sure you have good fuel pressure as well as spark and it still dosnt start the next step would be to run a compression test on the engine ,its very likely the timing belt may have jumped and this would cause a not start. If this is the cases you will find low compression on all cylinders.

You need to see at least 100 PSI on each cylinder to start the engine, if it is a lack of fuel,then try spraying starter fluid on throttle body and see if the engine runs or not. If not,then timing belt is the cause of this problem. This engine is a non interference engine and should be fixable. The cost for a new belt runs about 2.7 hours in labor plus about $57 for a new belt.

This details will help.
Thanks.

See below latest solved car problems :----

For all types of

Timing belt routing diagrams for cars and trucks?

Click the link below:---
http://technoanswers.blogspot.com/2011/10/timing-belt-routing-diagrams-for-cars.html

For all types of 

Drive belt routing diagrams for cars and trucks?

Click the link below:---
http://technoanswers.blogspot.com/2011/10/drive-belt-routing-diagrams-for-cars.html


Car freeze overnight and started overheating while driving?

http://technoanswers.blogspot.com/2012/01/car-freeze-overnight-and-started.html





Mazda MPV cranks but will not start?

http://technoanswers.blogspot.com/2012/01/mazda-mpv-cranks-but-will-not-start.html

MAZDA MPV WILL CRANK BUT NOT TURN OVER TO START?





Labels: ford escort will not start, Fuel pressure and spark is good but ford escort will not start, starting issues on ford escort
Subscribe to: Posts (Atom)

@

@