@

Showing posts with label no start. Show all posts
Showing posts with label no start. Show all posts

Sunday, September 22, 2013

Engine Will Not Start,Starter Turns ON

Starter spinning but the engine will not Crank


There are few possibilities that can cause the problems:---

The starter drive on your starter is faulty.

The starter drive is not engaging the flywheel to crank the engine.

The flywheel issue.The flywheel has some cracked or broken teeth that stops the starter from engaging.

Understand the starter system of the vehicle:---

On some starter the solenoid is mounted on top of the starter. 

Now When the ignition key is turned to ON, the solenoid paths current to the starter motor and at the same time pulls a lever that forwards the drive gear mechanism out so it will engage the flywheel and crank the engine. 

But when solenoid is weak or damaged, it may not be strong enough to overcome the spring tension that retracts the drive gear. So the starter spins but doesn't crank the engine. In your case this might be happening and that is what causing the problem.

On other type of starter assembly the solenoid is mounted remotely. In this starters when the starter motor starts to spin, it ratchets out so the drive gear will engage the flywheel and crank the engine. In this case if the drive mechanism is damaged or hung up, the motor may spin but not crank the engine.

In any case the starter motor has to be removed out to inspect the starter.

WHY ENGINE WILL NOT START:

This are due to few possible reasons.
What exactly any working engine needs to start?

Engine requires sufficient cranking speed, good compression, adequate ignition voltage (with correct timing) and fuel (a relatively rich air/fuel mixture initially). So whenever an engine is not able to start, any of the following is not performing.

If the engine won't crank, you are probably dealing with a starter or battery problem. 

If an engine cranks but refuses to start, it lacks ignition, fuel or compression.

When the engine cranks ordinarily but won't start, you need to check ignition, fuel and compression. Ignition can be checked with a spark tester or by positioning a plug wire near a good ground. 
No spark? The most likely causes would be a failed ignition module, distributor pickup or crank position (CKP) sensors.

Friday, May 10, 2013

Dodge Cummins 2500 Has Starting Issues

Dodge Cummins Hard To Start


98 Dodge cummins 24 valve, slow to start. 


  • Batteries seemed weak. 
  • Batteries on long cranks attempting to start. 
  • When vehicle is jump start  heard clicking, then nothing. 
Now, with charged batteries, no sound at all when I turn the key. Both batteries show 12.6 volts. When the key is turned the batteries drop to 11 and change while the grid heater and lift pump run, then pop back to 12+, but no drop when the key is turned to start.

Engine Cranks But Wont Start

For an engine to run, you require three factors to happen within the engine, compression, fuel and ignition, without any one of these factors the engine will not run.

What Is Compression - Engine compression triggered by crankshaft rotation and pistons moving up and down within the engine block. If the timing belt or timing chain fails it will cause the camshaft to become out of connection with the crankshaft or allow the camshaft to stop rotating. Either of these conditions will cause the engine to drop compression and sometimes cause inner engine damage.

Fuel Delivery System - The fuel system includes: fuel pump, fuel injectors, pressure regulator, fuel filter and pressure lines. This system is used to deliver fuel under pressure to the fuel injection system, the shortage of fuel pressure or volume will cause the fuel delivery system to fail and the engine to stall or not start.

Ignition Spark Delivery System - The ignition system components include: spark plugs, spark plug wires, distributor (if applicable), crankshaft angle sensor, camshaft angle sensor, ignition coil, ignition module, knock sensor and PCM (powertrain control module). The engine is dependent on the ignition spark to be delivered to the combustion camber at the appropriate time. If the ignition spark quits or is supplied at the wrong time the engine will not run or run poorly.


Troubleshooting:


Check Starter Relay Fuse

It's very possible that the starter relay fuse blew. When the starters on these trucks started to fail and draw too much current it would cause the fuse to blow, sometimes intermittently at first.

Location Of Starter Relay Control Fuse:

The first thing you'll want to do is check fuse 2 in the power distribution center under the hood and hopefully it's blown. Swap in a known good fuse or check it with an ohm meter if possible if you can't see anything visibly wrong with it.

Confirm Wiring And Fuse Issue:

If it's blown then replace it, remove the small wire from the starter solenoid and turn the key to the crank position. If the fuse doesn't blow this way then you know there isn't a wiring issue, if it blows with the solenoid plugged in but not unplugged then the starter will need to be replaced.


This will help.
Thanks.

ALSO VIEW THIS RELATED:

For Car parts and diagrams:

CAR MANUAL GUIDE
                 
FOR FREE MANUALS AND GUIDES: ---
Car repair guide?


For all types of car repair help:



Car Backfires

For car repair How to guides:


OVERHEATING: Radiator Fan Not Working

Engine Cooling Fan not Working


"Radiator fan"  "Engine Fan"  "COOLING FAN WILL NOT TURN OFF"

LIFT GATE / TAIL GATE ISSUES

TRUNK WILL NOT OPEN


CAR ALARM ISSUES


Car starter removal, Starter motor testing, Starter repairs, Starter solenoid, Starter wiring,


DOOR PANEL REMOVAL, car door panel, door panel components, front door panel, rear door panel,


HEATER CORE REPLACEMENT, HEATER CORE REMOVAL, TROUBLESHOOT HEATER CORE, FLUSH HEATER CORE,

CAR POWER SEAT, ELECTRIC SEAT, POWER SEAT WILL NOT WORK, SEAT WILL NOT GO FORWARD,



For all types of---------

Timing belt routing diagrams for cars and trucks?



                          

==========

For all types of --------

Drive belt routing diagrams for cars and trucks?




stalling issues:
Engine stalls, car stalls while starting, vehicle stalls while starting, Engine stalls and dies, Car stalls and stops,


CRUISE CONTROL Not working, cruise control replacing, troubleshooting cruise control problems,


TRANSMISSION PROBLEMS:

NO REVERSE ON TRANSMISSION

GEAR SHIFT ISSUES

Transmission fluid leak, transmission gears slip,


TRANSMISSION REPLACING AND TROUBLESHOOTING, INSPECTING TRANSMISSION COMPONENTS, TRANSMISSION FAILURES, OD WARNING LIGHT,


TRANSMISSION FLUID FILLING, WHERE TO FILL TRANSMISSION FLUID, AUTOMATIC TRANSMISSION FLUID, NO TRANSMISSION DIPSTICK,


WINDSHIELD WIPERS, WINDSHIELD WIPERS NOT WORKING,WIPER MOTOR MAKING NOISE,NO WIPERS,WIPER FLUID LEAKS,WIPER FUSE AND RELAY,


COOLANT LEAK ISSUES, COOLANT LEAK PROBLEMS, COOLANT SENSOR, LOW COOLANT,


BRAKE LIGHTS NOT WORKING, REPAIRING BRAKE LIGHTS, NO BRAKE LIGHTS,


CHECK ENGINE LIGHT,ENGINE WARNING LIGHT FLASHING,ENGINE LIGHT ON DASH,DASHBOARD WARNING LIGHT,ECM ERROR CODES,


DASHBOARD WARNING LIGHTS ARE ON, ENGINE LIGHT ON DASH,WARNING LIGHTS STEADY ON DASH,RESET DASH BOARD WARNING INDICATOR,


KEYFOB PROGRAMMING, REPROGRAMMING CAR KEY, KEYLESS ENTRY RESET,ANTITHEFT WILL NOT LET CAR TO START, ANTI THEFT ISSUES, KEYFOB NOT WORKING, KEYLESS ENTRY QUIT WORKING,


IGNITION KEY WILL NOT RELEASE, IGNITION KEY STUCK UP, KEY WILL NOT COME OUT OF IGNITION, FAULTY IGNITION KEY LOCK CYLINDER, REPLACING IGNITION CYLINDER,


HEATER ISSUES:

HEATER NOT BLOWING COLD,NO HOT AIR FROM HEATER,A/C BLOWS HOT AIR,A/C NOT BLOWING COLD, COLD AIR FROM HEATER,BLEND DOOR ACUTATOR CLOSED,HVAC UNIT NOT OPERATING,



HEATER NOT BLOWING COLD,NO HOT AIR FROM HEATER,A/C BLOWS HOT AIR,A/C NOT BLOWING COLD, COLD AIR FROM HEATER,BLEND DOOR ACUTATOR CLOSED,HVAC UNIT NOT OPERATING,



STEERING ISSUES:

POWER STEERING TROUBLESHOOTING, STEERING SQUEAKS, POWER STEERING FLUID LEAKS, FAULTY POWER STEERING PUMP, POWER STEERING NOT WORKING, POWER STEERING BELT,



VEHICLE STARTING ISSUE:

CAR NO START: ENGINE NOT TURNING OVER:

Wednesday, May 1, 2013

jeep Grand Cherokee turns over but no start

Jeep Grand Cherokee will not start


Turns over but no start problem on 99 jeep grand Cherokee limited 4.7


Troubleshooting No start problem:

1) Take Test light and voltmeter.


  • Unplug one of the coils or fuel injectors and find the dark green/orange wire. This is for the ASD relay.


  • Ground the black lead of your voltmeter and set it to 20v DC. Use the red lead to probe the dark green/orange wire in the connector.


  • This wire should power up for about a second when the key is first turned on and then it should stay powered up constantly when cranking. Check both situations and let me know what you see.
Result: When i put the key forward on the on position is 10.90 and when i start it up is 10.82.



2) Did you check for spark on just one cylinder or did you check at least a couple cylinders? Did you check by inserting a spark plug or spark tester in the end of the coil, grounding the test or plug and cranking the engine over?

Result: removed the 2 front coils one from each side,and no spark.


No Spark On Jeep Cherokee

For this case first check for any codes set.


  • If there is still nothing set then disconnect the cam sensor. The cam sensor is mounted on the side of the right bank cylinder head just forward of the exhaust manifold. It's held in with a single bolt and has a three wire electrical connector.

i suggest to disconnect the cam sensor, crank the engine for ten seconds and see if it sets a P0340.

  • There are multiple possibilities for this problem. If there are no codes setting on their own then that makes it tougher to diagnose since anything that causes a loss of spark should set a code. If you can get a code reader or scan tool on it and do this simple test that would be great.

Please Note you have to unplug cam sensor and not crank sensor.


The crank sensor is the sensor in the right rear of the block by the starter. The sensor we want to unplug is the cam sensor, which is on the right cylinder head just forward of the exhaust manifold. 

About camsensor i would like to say: You can feel it from the top but not see it, but you should be able to see it (but probably can't reach it) if you look up from the bottom.

See cam sensor shown below in the diagram:

camshaft sensor

Location of Jeep Grand Cherokee cam sensor. It's on the right side of the right cylinder head just forward of the exhaust manifold. If you face the engine from the front find the oil fill housing and then move your hand around the side of the cylinder head from there. Before you get to the exhaust manifold you'll find the cam sensor.

Result: I got error P0340.

NOW disconnect crank sensor and see what code you get:


Let's disconnect the crank sensor now too along with the cam sensor. Crank the engine again and see if it sets a P0320 also.

If so, then we'll clear the codes, plug the cam sensor back in, crank it and see if it sets just a P0320. 

WHY TESTING THE ERROR CODE IS NECESSARY?

The reason for unplugging the crank sensor and seeing if it sets a code is because we don't really have the equipment to see if the sensors are producing a signal. 

Problem noticed is Loss Of Spark:

Nothing should cause a loss of spark without setting a code. I think what may be happening is the cam sensor is causing the crank sensor to not produce a signal.


Understanding Cam Sensor And Crank Sensor:

The cam and crank sensors share a sensor ground and a 5v reference voltage, the third wire at each sensor is the signal wire and goes to the PCM. What sometimes happens is the cam sensor will short internally and take down the crank sensor's 5v reference. When this happens the PCM doesn't know the engine is turning, so there will be no codes yet no spark.

Reason For Unplugging the Crank sensor:

By unplugging the crank sensor and cranking the engine with the cam sensor plugged in that would allow us to see if it will set a crank sensor code or not. If it didn't set a code with it unplugged then we know the cam sensor is causing the issue.

Simple Solution Without Testing:

The alternative is to try replacing the cam sensor and see if that takes care of it. As per description it seems faulty cam sensor

If you don't want to get back to the crank sensor and unplug it then as a next step I'd recommend replacing the cam sensor. If you do I'd recommend a Mopar sensor as aftermarkets are known to cause problems even when new. Mopar parts are of very high quality and good performing parts.

Understand the Location of Sensor And Filter Parts:

The oil sender is on the left side of the front of the engine right next to the oil filter.

The cam sensor is on the right side of the right cylinder head just forward of the exhaust manifold. Find the oil filler neck and slide your hand around the right side of the head toward the manifold and you'll find the cam sensor. See picture of it's location mentioned above, the picture is the right side of the engine and cylinder head as viewed from the right front fender area. 

The air filter box is on the left side of the engine compartment so removing it won't help. You can try removing the battery from the right side if you want and that will give you a little better access to the area.

This details will help.
Thanks.

ALSO VIEW THIS RELATED:

For Car parts and diagrams:

CAR MANUAL GUIDE
                 
FOR FREE MANUALS AND GUIDES: ---
Car repair guide?


For all types of car repair help:



Car Backfires

For car repair How to guides:


OVERHEATING: Radiator Fan Not Working

Engine Cooling Fan not Working


"Radiator fan"  "Engine Fan"  "COOLING FAN WILL NOT TURN OFF"

LIFT GATE / TAIL GATE ISSUES

TRUNK WILL NOT OPEN


CAR ALARM ISSUES


Car starter removal, Starter motor testing, Starter repairs, Starter solenoid, Starter wiring,


DOOR PANEL REMOVAL, car door panel, door panel components, front door panel, rear door panel,


HEATER CORE REPLACEMENT, HEATER CORE REMOVAL, TROUBLESHOOT HEATER CORE, FLUSH HEATER CORE,

CAR POWER SEAT, ELECTRIC SEAT, POWER SEAT WILL NOT WORK, SEAT WILL NOT GO FORWARD,



For all types of---------

Timing belt routing diagrams for cars and trucks?



                          

==========

For all types of --------

Drive belt routing diagrams for cars and trucks?




stalling issues:
Engine stalls, car stalls while starting, vehicle stalls while starting, Engine stalls and dies, Car stalls and stops,


CRUISE CONTROL Not working, cruise control replacing, troubleshooting cruise control problems,


TRANSMISSION PROBLEMS:

NO REVERSE ON TRANSMISSION

GEAR SHIFT ISSUES

Transmission fluid leak, transmission gears slip,


TRANSMISSION REPLACING AND TROUBLESHOOTING, INSPECTING TRANSMISSION COMPONENTS, TRANSMISSION FAILURES, OD WARNING LIGHT,


TRANSMISSION FLUID FILLING, WHERE TO FILL TRANSMISSION FLUID, AUTOMATIC TRANSMISSION FLUID, NO TRANSMISSION DIPSTICK,


WINDSHIELD WIPERS, WINDSHIELD WIPERS NOT WORKING,WIPER MOTOR MAKING NOISE,NO WIPERS,WIPER FLUID LEAKS,WIPER FUSE AND RELAY,


COOLANT LEAK ISSUES, COOLANT LEAK PROBLEMS, COOLANT SENSOR, LOW COOLANT,


BRAKE LIGHTS NOT WORKING, REPAIRING BRAKE LIGHTS, NO BRAKE LIGHTS,


CHECK ENGINE LIGHT,ENGINE WARNING LIGHT FLASHING,ENGINE LIGHT ON DASH,DASHBOARD WARNING LIGHT,ECM ERROR CODES,


DASHBOARD WARNING LIGHTS ARE ON, ENGINE LIGHT ON DASH,WARNING LIGHTS STEADY ON DASH,RESET DASH BOARD WARNING INDICATOR,


KEYFOB PROGRAMMING, REPROGRAMMING CAR KEY, KEYLESS ENTRY RESET,ANTITHEFT WILL NOT LET CAR TO START, ANTI THEFT ISSUES, KEYFOB NOT WORKING, KEYLESS ENTRY QUIT WORKING,


IGNITION KEY WILL NOT RELEASE, IGNITION KEY STUCK UP, KEY WILL NOT COME OUT OF IGNITION, FAULTY IGNITION KEY LOCK CYLINDER, REPLACING IGNITION CYLINDER,


HEATER ISSUES:

HEATER NOT BLOWING COLD,NO HOT AIR FROM HEATER,A/C BLOWS HOT AIR,A/C NOT BLOWING COLD, COLD AIR FROM HEATER,BLEND DOOR ACUTATOR CLOSED,HVAC UNIT NOT OPERATING,



HEATER NOT BLOWING COLD,NO HOT AIR FROM HEATER,A/C BLOWS HOT AIR,A/C NOT BLOWING COLD, COLD AIR FROM HEATER,BLEND DOOR ACUTATOR CLOSED,HVAC UNIT NOT OPERATING,



STEERING ISSUES:

POWER STEERING TROUBLESHOOTING, STEERING SQUEAKS, POWER STEERING FLUID LEAKS, FAULTY POWER STEERING PUMP, POWER STEERING NOT WORKING, POWER STEERING BELT,



VEHICLE STARTING ISSUE:

CAR NO START: ENGINE NOT TURNING OVER:

Saturday, February 9, 2013

2005 Chrysler 300C: Has No Heat & Also has No start Problem

Troubleshooting No Heat And No Start Problem

Its 2005 Chrysler 300C, :
The problem Description:
While I was driving I heard a noise like a hose had broken followed by the noise and after that  heater  no longer worked I then heard a sound like something was dragging under my car. Then I noticed that there was a lightening bolt symbol and a slippery or loss of traction symbol.

Now my car will not start.
Please Help?


Follow Troubleshooting:-----


From your description it sounds like you may have lost a radiator or heater hose, allowed the coolant to escape and kept driving while it severely overheated. And that is what you noticed.

The first thing you'll need to do is check the coolant level and look around the engine compartment for sprayed coolant and the damaged hose or cooling system component. 

Also let me know  what happens when you try to start the engine, does it not crank? See if it cranks now that it has cooled off overnight. When severely overheated and driven that way catastrophic engine damage can be done.


Clients Reply:

The engine just make whine noise and will not start.
And as per your details No coolant was found the reservoir was completely empty and mechanic says that most likely the engine will not start again.

What are potential options for replacement? Can the engine for this model be replaced with that of a lower model or does it have to be the same 5.7L hemi?

EXPERT'S REPLY:


As per my experience there are a few options for replacement.

Most expensive would be a Mopar or aftermarket re-manufactured engine.
The cost will be very high for this brands, but benefit is you would have the longest warranty and would last the longest. There will be quite a few options available at different parts stores and suppliers, warranty and prices will vary.

Other option is try to find a used engine from a salvage yard. This will be the cheapest way to fix it but likely wouldn't last as long as a re-manufactured engine, unless you were able to find a low mileage unit. Replacing it with a used engine would be the cheapest route.

This car also came with either the 2.7 or 3.5 engine models, but swapping one of those in would be more expensive in the long run. You'd need all engine accessories, exhaust, complete wiring harness, fuel and evaporation emissions lines, the transmission and powertrain control module from a six cylinder car. If you decided to do this it would be cheapest to try to find a wrecked six cylinder car to take all the components from.

Also Note one more thing the Replacement unit comes with two types, short blocks and long blocks

A short block is the block, crank, pistons and cam. A long block is the same but comes with the cylinder heads and valvetrain. If yours has been overheated then you're going to need a long block as the heads won't be reusable.

I suggest get the help of professional mechanic who knows these job very well.Do it yourself will not be that easy to complete these task properly.

Hope all goes well.






Dodge Ram will not start

No Start Problem on Dodge Ram


It used to start and run but it dies n few seconds.

Can it be security or kill switch problem.

The red "security" light is lit up, but that light is always been on.

Also Error codes are there on super chip,P0513 invalid skim key.

The vehicle is diesel engine 5.9 2006 Dodge Ram

The red light on dash board is blinking when these happens.


OK, Here is the troubleshooting details for these problem 


The engine is dying because of the SKIM system.
The SKIM System  uses a transponder chip in the key that communicates with a module in the steering column, the wireless control module (WCM).

For these particular case as per our garage repair experience you either have a failed key or a failed WCM. It's starting and dying with the Security light flashing because the ECM, WCM and key don't all agree.

Usually disconnecting the battery or puling the IOD fuse will allow a locked up WCM to work again, but not always. 

Now to know at fault is stored in your case.A scan tool is going to need to be used to see what fault codes have set and go from there. Either the key has failed and isn't being recognized by the WCM or the WCM itself is the issue. Both are possible.There will be stored fault codes that are necessary as a basis for diagnosis and then a dealer level scan tool along with a special code obtained from Chrysler are going to be necessary to program the replacement part, whichever it is.

If the Security Light had been coming on by itself in the past but the engine ran fine then there is a good chance the WCM was causing that and is likely the issue now. There have been many more WCM issues with these trucks than key issues.


The P0513 is going to be related, it sets when the SKIM key code doesn't match the SKIM module. You've either got a failed key or WCM. If the WCM was damaged when the truck was broken into that would explain the issue happening right afterward.

As per my knowledge and experience it's not going to just be a fuse, it will either be a failed WCM or key. Either way it's going to take a dealer level scan tool and a code obtained from Chrysler's database to repair the issue, so a dealer or a mechanic with the proper equipment is going to be necessary.

Friday, January 25, 2013

Chrysler TC by Maserati: 1989 Chrysler TC by Maserati will turn over but not start


TURNS OVER BUT NOT START

QUESTION:



Its 1989 Chrysler TC by Maserati with 40k mi. Vehicle has been parked in garage for nearly last 2 years. Now while starting (after replacing battery) it turns over but does not start. A nearby mobil auto mechanic check it out and said injectors weren't receiving fuel. Auto technician replaced fuel pump and fuel filter but vehicle however does not start. Experimented with replacing fuel pump relay but still does not start.

What do you highly recommend?

(Note: mechanic did not depressurize the fuel system before replacing pump, but did attempt to depressurize it afterward by following service manual's guidelines to connect wires to prongs on plug in wiring harness at fuel rail (?) and connecting ends to positive terminal of battery and ground.

Now these is what he did.Is this the correct plug?

Do you think that the no start problem is caused by not depressurizing the system?)


At present there is spark received and fuel pump turns over for 2 seconds while turning the Key on.
Please help!!!!

==========

EXPERT ANSWER:


According to me it appears like the issue is with reduced power to the fuel pump resulting in these dilemma.
The pump could be lacking power but it might also be losing ground.

Did your mechanic examined to ensure that there are two power feeds to the relay with the key on?

If not get it done,these will help to confirm the problem.

To execute these test you'll possibly need to check with a test light or voltmeter. There must be two power feeds there.

If power is ok then jump connection between pin 30 and 87 of the relay and see if the fuel pump turns on.

If it does not come on then the second step is access the pump again to check power and ground to see which it's missing and go from there.

Suppose if the relay power feeds are ok but there is no power at the pump when it's jumped then the wire is damaged in between someplace and the circuit will possibly need to be hardwired or the split located and fixed.

If the pump does in fact have power but is missing ground then it's either going to be a wiring issue or a corroded ground.

So all in all here are fairly a few possible issues and it's going to take some tests to figure out exactly why the pump isn't operating. You can start by verifying the power feeds, jump the relay and see what happens, and then check for power and ground if required.

These details will help.
Thanks.



Users Who Viewed This Problem Also Viewed:


What to Do When Car Turns Over But Won't Start?
http://technoanswers.blogspot.com/2012/11/what-to-do-when-car-turns-over-but-wont.html


1989 Toyota Pickup Truck: Turns over but not start?

http://whatisbyme.blogspot.in/2012/05/1989-toyota-pickup-truck-turns-over-but.html



Engine turns over but will not fire or start?

http://technoanswers.blogspot.in/2012/07/engine-turns-over-but-will-not-fire-or.html


Car will not start?

http://repairhelpcenter.blogspot.in/2012/02/car-will-not-start.html

Car turns over, but only starts, if starter is jumped?

http://schematicsdiagram.blogspot.com/2011/12/car-turns-overbut-only-startsif-starter.html

Car turns over but will not start, only makes clicking sound?

http://schematicsdiagram.blogspot.com/2011/12/car-turns-over-but-will-not-startonly.html




Sunday, October 7, 2012

Landcruiser prado won't start

Toyota Model Landcruiser Prado vehicle will not start.

There are many types of no start issues which other Toyota users have noticed.
As we are from garage repair field.We directly deal with such issues.

I will share some of such issues with you,with there troubleshooting details.

The Problem noticed like

ISSUE 1:---

Landcruiser makes click click noise but will not start

When you turn the key to start the car the On dash ignition lights come on right but when turned to 'Start' just a click and then nothing happens.

In these types of cases first see if there is any type of warning light coming up on dash or not.
If check engine light comes up on dash and remains steady ON or remains flashing.Then this is indication of error codes stored in vehicles computer module.
The vehicle needs to be scanned for retrieving error codes stored in it.

But if there is no such engine light or warning light coming up on dash,then in that case the problem has to be traced manually.

On some cases with the above mentioned problem,the problem goes away if the vehicle is turned off and turned on again.

But in such types of cases the most possible culprit is faulty or weak starter motor and starter motor solenoid.
This issue is caused by crap/burning out of the solenoid contacts within the starter motor.And at last the click click noise is heard while start up.The starter motor and solenoid tries to engage,but because this components gets weak,it does not start.

ON SOME CASES THE SAME ISSUE IS NOTICED DUE TO FAULTY BATTERY OR WEAK BATTERY OR LOOSE BATTERY TERMINALS.

In that case,you have to get the battery tested.There is a basic simple procedure to get the battery tested.


Turn the car off. Make sure all the interior lamp/ lights in the vehicle are off. If any light is ON then the power gets consumed from the battery. Once everything is confirmed OFF.Then start the battery test.
The battery surface voltage with a Multimeter positive on the meter to positive on the battery terminal & negative on the meter to negative on the battery terminal.
You should get  approx 12 volts or near to that.
If the voltage is too low or very low then its clear that battery needs recharging.
But if battery is very old then in many case the battery needs to be replaced.This is because old batteries get weak internally and don't get charge properly or don't hold the charger for longer periods like newer batteries hold.


ISSUE 2:---


Toyota Landcruiser Prado just cranks but will not start.

This problem says that everything is normal.The vehicle has power to crank the engine ,but its not starting.

In such cases mostly is issue is with weak or faulty fuel pump & Fuel filter.
When this components gets old,the required amount of fuel does not reach engine to get the vehicle started.The particular amount of pressure is required,to make the vehicle start.If the fuel pressure is less,the engine will crank,but will not be able to start.

On same problem with diesel engine vehicles the issue is with faulty or dirty glow plugs.Inspecting the glow plugs helps.



ISSUE 3:---


On one of our customers old model land cruiser.It was of year 1991 Toyota Land cruiser.

The vehicle was not getting started and no check engine light on dash.

The issue was faulty ELECTRONIC FUEL INJECTION RELAY.These relay got short and was causing the no start issue.After replacing these relay the vehicle started fine.
These relay is located in the fuse box under hood.


Users Who Viewed This Problem Also Viewed:

2007 ford expedition engine cranks but wont start

http://technoanswers.blogspot.com/2012/10/2007-ford-expedition-engine-cranks-but.html

Vehicle Cranks Fast but Won't Start

http://whoisbyme.blogspot.in/2012/07/vehicle-cranks-fast-but-wont-start.html

Car won't start without hitting the gas pedal?

http://schematicsdiagram.blogspot.com/2011/12/car-wont-start-without-hitting-gas.html

Car won’t start when cold?

Car won't start after sitting overnight?

Car loses power while acceleration?

http://schematicsdiagram.blogspot.com/2011/12/car-loses-power-while-acceleration.html

Car suddenly died and won’t start?

http://technoanswers.blogspot.in/2012/02/car-suddenly-died-and-wont-start.html

Car is starting but not turning over?


http://technoanswers.blogspot.in/2012/02/car-is-starting-but-not-turning-over.html

Engine cranks but will not start?

http://technoanswers.blogspot.in/2012/02/engine-cranks-but-will-not-start.html




Saturday, October 6, 2012

2007 ford expedition engine cranks but wont start

Engine cranks fine but will not start



A common problem,noticed on many other vehicles too.

On this cases first see if the check engine light is coming on and remaining steady or blinking.

In any cases,getting the vehicle scanned helps.
At autozone service centers its free to get vehicle scanned.

But if no error code stored or no codes retrieved in diagnostics then for troubleshooting,you have to test and inspect few common parts manually.


When you turn the key to the start position, What does the red theft light in the dash do?



Inspect this light properly,Does it blink fast, stay on or go out?


If it blinks faster than normal you may have an anti theft problem but, If you hear a clicking noise coming from the engine compartment, this may be the sign of a weak battery with not enough cold cranking amps to turn over the starter or a faulty starter motor.

In this case,try jump starting the vehicle and see,if it starts fine by jump start,then its isue with weak battery or loose battery to start connections.
Get the vehicle checked with replacement battery.


Yes, the vehicle could have 12 volts which is what is needed to run all lights and accessories but the cranking amps are what is needed to turn over the starter as it requires a high amperage.

But if battery and other voltages,including starter checked ok,then the next thing to be checked is fuel system.

Try starting with starter fluid on throttle body and see if vehicle is running with starter fluid or not.
If yes then issue is with faulty or weak fuel pump or the fuel filter is dirty and needs to be cleaned or replaced.

Also before replacing fuel pump,get the inertia switch checked.


You have to check power coming into the inertia switch and power going out, if that's good then so far its looking like a new fuel pump is in order

There are two wires coming from inertia switch.The inertia switch wires should give the same voltage of what the car battery voltage is.
The battery voltage should be 12 volts.So the wires on inertia switch should give approx 12 volts.

The inertia switch for your vehicle is located behind the removable trim panel in the left side rear of the vehicle.

 If the above troubleshooting details do not help.Then the problem is related to faulty sensors.Both camshaft sensor and crankshaft sensor.First  replace the camshaft position sensor. If that doesn't fix it; replace the crankshaft position sensor.

But if any of these sensors are faulty,then in vehicle scan diagnosis,you should get error codes,pointing out these sensors to be faulty.


These details will help.
Thanks.


Users Who Viewed This Problem Also Viewed:

For All types of Car models and brands help 
Go to Newly Launched

FREE Car repair guide? 
http://technoanswers.blogspot.in/2012/03/car-repair-guide.html 

& 
Complete Car repair Help FREE? 
http://repairhelpcenter.blogspot.in/2012/03/complete-car-repair-help.html

Ford Expedition and Lincoln Navigator Repair Guide?

http://technoanswers.blogspot.in/2012/03/ford-expedition-and-lincoln-navigator.html


1997 Oldsmobile Cutlass Ciera: The Engine cranks but not start?

http://schematicsdiagram.blogspot.in/2012/04/1997-oldsmobile-cutlass-ciera-engine.html










@