@

Showing posts with label key fob programming. Show all posts
Showing posts with label key fob programming. Show all posts

Monday, February 20, 2012

Theft indicator not letting car to start?

Security system causes such problems many a times.Some times normal reset helps,but in some cases the system has to reset by dealer.

First try this procedure:----
Let the car sit off for 10 - 15 minutes, then try to start it. Check the owners manual if you have it. Sometimes, on various cars letting them sit awhile will allow the system to reset itself. On others sometimes rapidly turning the key from off to on, without turning to start 3 to 8 times within 10 seconds and then on the last turn to the on position leave it there until the horn chirps, at that point turn the key directly to start, or turn off first and turn to start. If all this fails, a GM dealer can reset the system.

One more procedure you can try:---
Insert  key in ignition and turn all the way as to start the car, but without actually starting it(security light will be flashing). Leave it on for ten minutes until the security light becomes solid, now turn off and start the car.
And see if it starts or not.If not,then the problem is the ignition lock cylinders are worn out and makes the car think that it's being stolen. The dealer needs to replace the ignition switch and re-key the cylinder. It's expensive too. Basic cost $750 to repair.

This details will help.
Thanks.

Car not starting or turning over indicates towards multiple possibilities. It can be issue with battery or weak battery. But if battery checks out ok, then it can be starter issue or faulty alternator or problem with low fuel pressure or no spark at spark plugs due to dirty spark plugs or faulty ignition coil or injectors getting cracked or dirty and needs to be cleaned.
                     
To confirm the problem, the basic troubleshooting is required.

Click this link below and follow the troubleshooting:------
---------

Where is Key chip memory located on 2004 ford Freestar?

http://technoanswers.blogspot.com/2012/01/where-is-key-chip-memory-located-on.html

Ford Keyless Remote Fob Reprogramming?

http://schematicsdiagram.blogspot.com/2011/12/ford-keyless-remote-fob-reprogramming.html

After getting car washed, check engine light is ON and key less entry not working, tried reprogramming. Also car shows fuel pressure?


Can car radio code block Passkey anti theft system ?

Toyota Avalon Factory Alarm will go off?

http://repairhelpcenter.blogspot.com/2012/01/toyota-avalon-factory-alarm-will-go-off.html

After Alternator failure the Keyless keypad on drivers door stopped working?

http://technoanswers.blogspot.com/2012/01/after-alternator-failure-keyless-keypad.html

Audi A8 Key Fob Programming?

                

Oldsmobile Aurora Key Fob Reprogramming?

Buick Lesabre Key Fob Reprogramming?


Keyfob remote not working on 2003 Ford E350 Econoline?

KeyFob will open the doors but not start on BMW?

Key Fob will not lock and unlock doors?

http://technoanswers.blogspot.in/2012/02/key-fob-will-not-lock-and-unlock-doors.html


This will help.
Thanks

Saturday, December 10, 2011

Audi A8 Key Fob Programming?

Key fob Programming.Yes its possible.But in some cases the programming dont work.This is due to two reasons.
Either you have not tried the procedure correctly or on your car the manual Key Fob Programming is not supporting.In that case I'm afraid its job for a dealership or a auto locksmith as you need someone with the OBD tools to plug into the car and re-code the key.Also all the keys have to be re-coded at the same time otherwise you'll get the new out of sync with the old.

Now the Key Fob Programming procedure is as follows :----------
First check that the battery in the key-fob is in good condition ( typically needs replacing every 5 years or so)
Re-code as follows:
1. Switch Ignition ON and leave the key in the ignition.
2. Mechanically lock the vehicle using the Drivers door using a second key.
3. Using the remote control press the Unlock button once, and the horn will sound once.
4. Wait 6 seconds and press the unlock button once to activate the coding procedure. The remote control will now be programmed.

NOTE : When performing programming on additional remotes the procedure is the same, except you press the unlock button 2, 3 or 4 times for the different remote.
For example : If programming 2 remotes press the unlock button twice with a 1 second interval between each press, repeat for 3 and 4 remotes.

5. Switch Ignition OFF.
6. Remove key from ignition and check for operation.
7. The coding procedure can be repeated up to 4 times for additional remotes.
8. The ignition must be switched OFF between programming each remote control.

In most of the cases this procedure help.Hope in your case also it should work.
-------------
This basic details will help.Thanks.
------------------
If you need dis-assembly or replacement instructions for any other auto/car part, or you want to ask question related to your car/truck jeep problem then please leave the comment with your details, so I can provide you the required instructions and solutions.


For related solutions,see the list below:---

After getting car washed, check engine light is ON and key less entry not working, tried reprogramming. Also car shows fuel pressure?

http://schematicsdiagram.blogspot.com/2011/12/after-getting-car-washedcheck-engine.html




@