2003 Chrysler Concorde Struggled to Accelerate

OBD Code P0700 on Chrysler

Check engine light ON and vehicle struggles to accelerate.

Also engine RPM goes high

I got the code by cycling the ignition key ON-OFF.
The procedure is on, off, on, off and then on


SOLUTION AND REASON FOR THESE PROBLEM:----




In your case the issue is in fact with the transmission instead of engine. What has happened is the transmission gone into limp-in mode, where it's restricted to second gear. For this reason it takes off sluggishly and engine RPM's are higher while driving a vehicle.

Now coming to the OBD error code which you got. P0700 sets in the engine controller when there's a fault code stored in the transmission control module.
On these case,
the first thing to be done is to diagnose the problem. These can be done once you  read the fault codes from the trans controller with a scan tool or code reader. Cycling the key will allow you to read codes from the engine controller only but not any of the other modules.
Most large parts stores like Autozone will read codes for free in the parking lot with a code reader.
Once you receive that codes you will get another OBD code for correcting the problem.



THE CUSTOMERS REPLY:-----

I received more error code when got my vehicle scanned at autozone the first code was similar which i manually retrieved by cycling ignition key but one more OBD code i received is P1776

THE EXPERTS REPLY:---





As mentioned previously
The P0700 just sets in the engine controller when there is a code stored in the trans controller. So just ignore Error code P0700.

The one related to the actual problem is the P1776.

The explanation for Error code P1776 :-----

P1776 sets because solenoid switch valve in the transmission valve body gets blocked in the low/reverse position or the transmission control module (TCM) does not get that solenoid switch valve is in correct position.


WHAT IS SOLENOID SWITCH VALVE?
The solenoid switch valve is a valve in the valve body that allows the same solenoid to be used to apply either the low/reverse clutch or the torque converter clutch. It moves backwards and forwards in a bore to direct fluid in either direction.


HOW EXACTLY TCM KNOWS THAT FLUID IS REQUIRED?
These is done by pressure switches.In the solenoid pack mounted on top the valve body there exists a series of pressure switches that tells the TCM when there is fluid pressure in the different hydraulic circuits.

When the P1776 sets it's because the low/reverse pressure switch has indicated fluid pressure on the low/reverse circuit when the torque converter clutch should have been turned on.


REASONS FOR THESE ERROR CODE TO OCCUR?

Here are a few possibilities that can cause this. It could be wiring or the TCM itself but that would be rare.

A solenoid switch valve sticking.
They can wear into the soft aluminum bore over time and start to stick and cause this code to set.

Another possibilities failed low/reverse pressure switch, and this is the most common cause for the code.

As I talked about before that the pressure switches are located in the solenoid pack, and they're serviced with the solenoid pack. There were many solenoid packs in this time frame that were identified as built with suspect pressure switches in them.

I suggest to replace the solenoid pack and while the valve body is out, without forget inspect the solenoid switch valve bore and polish it up if required. The solenoid pack is almost surely the cause of your problem but since the valve bore does wear a bit I always make sure it's in good condition before re-installing the valve body.

These details will help.
Thanks.

Users Who Viewed This Problem Also Viewed:

2004 Dodge town & country: Jerks and Hesitates During Acceleration?

http://technoanswers.blogspot.in/2012/07/2004-dodge-town-country-jerks-and.html

Engine accelerates when brake is applied?

http://technoanswers.blogspot.in/2012/02/engine-accelerates-when-brake-is.html

Loss of acceleration?

http://technoanswers.blogspot.in/2012/02/loss-of-acceleration.html

How exactly the Vehicles Accelerator Cable works?

http://repairhelpcenter.blogspot.com/2011/11/how-exactly-vehicles-accelerator-cable.html

How exactly Vehicles Accelerator Pump Diaphragm Works?

http://repairhelpcenter.blogspot.com/2011/11/how-exactly-vehicles-accelerator-pump.html

2000 Toyota Avalon: Engine Lean Codes and Knock Sound on Acceleration?

http://whatisbyme.blogspot.in/2012/05/2000-toyota-avalon-engine-lean-codes.html

Chrysler TC by Maserati: 1989 Chrysler TC by Maserati will turn over but not start

TURNS OVER BUT NOT START

QUESTION:

Its 1989 Chrysler TC by Maserati with 40k mi. Vehicle has been parked in garage for nearly last 2 years. Now while starting (after replacing battery) it turns over but does not start. A nearby mobil auto mechanic check it out and said injectors weren't receiving fuel. Auto technician replaced fuel pump and fuel filter but vehicle however does not start. Experimented with replacing fuel pump relay but still does not start.

What do you highly recommend?

(Note: mechanic did not depressurize the fuel system before replacing pump, but did attempt to depressurize it afterward by following service manual's guidelines to connect wires to prongs on plug in wiring harness at fuel rail (?) and connecting ends to positive terminal of battery and ground.

Now these is what he did.Is this the correct plug?

Do you think that the no start problem is caused by not depressurizing the system?)


At present there is spark received and fuel pump turns over for 2 seconds while turning the Key on.
Please help!!!!

==========

EXPERT ANSWER:


According to me it appears like the issue is with reduced power to the fuel pump resulting in these dilemma.
The pump could be lacking power but it might also be losing ground.

Did your mechanic examined to ensure that there are two power feeds to the relay with the key on?

If not get it done,these will help to confirm the problem.

To execute these test you'll possibly need to check with a test light or voltmeter. There must be two power feeds there.

If power is ok then jump connection between pin 30 and 87 of the relay and see if the fuel pump turns on.

If it does not come on then the second step is access the pump again to check power and ground to see which it's missing and go from there.

Suppose if the relay power feeds are ok but there is no power at the pump when it's jumped then the wire is damaged in between someplace and the circuit will possibly need to be hardwired or the split located and fixed.

If the pump does in fact have power but is missing ground then it's either going to be a wiring issue or a corroded ground.

So all in all here are fairly a few possible issues and it's going to take some tests to figure out exactly why the pump isn't operating. You can start by verifying the power feeds, jump the relay and see what happens, and then check for power and ground if required.

These details will help.
Thanks.

Users Who Viewed This Problem Also Viewed:

What to Do When Car Turns Over But Won't Start?

http://technoanswers.blogspot.com/2012/11/what-to-do-when-car-turns-over-but-wont.html

1989 Toyota Pickup Truck: Turns over but not start?

http://whatisbyme.blogspot.in/2012/05/1989-toyota-pickup-truck-turns-over-but.html

Engine turns over but will not fire or start?

http://technoanswers.blogspot.in/2012/07/engine-turns-over-but-will-not-fire-or.html

Car will not start?

http://repairhelpcenter.blogspot.in/2012/02/car-will-not-start.html

Car turns over, but only starts, if starter is jumped?

http://schematicsdiagram.blogspot.com/2011/12/car-turns-overbut-only-startsif-starter.html

Car turns over but will not start, only makes clicking sound?

http://schematicsdiagram.blogspot.com/2011/12/car-turns-over-but-will-not-startonly.html

Chrysler Sebring Touring: 2007 4dr Sebring 2.4 engine dies at idle

Chrysler Sebring 2.4 engine dies at idle

Engine dies at idle intermittently while at stop light or when engine gets warm

Question:

There is no check engine light, still scanned the engine module with no error code stored,the vehicle starts and runs fine with no problems but suddenly dies at idle without any indication.

Is it faulty PCM or any other know issue causing these problem?

Please Help !!!!!!!!1

Answer by expert:-

Thanks for asking your question here.

There are a few things I will mention below to troubleshoot these issue noticed on your vehicle:-----

• Primary will be software. We have seen a good number of software changes to the PCM, often with a TSB but just as often there are updates released with no TSB's or certification. The first thing to start is make sure the PCM software is up to date.If not then get the PCM software updated from nearest Chrysler dealer.

• Other then this i suggest you to get the crank sensor connector checked and inspected. If the connector seems faulty then i suggest to replace the crank sensor connector. Why i am suggesting to inspect and replace crank sensor because at our auto repair garage we have seen many such connector getting faulty causing same types of problem. And as per your vehicle model mentioned these early World engines had problems with terminal grip at the crank sensor connector and it will cause driveability issues and sometimes crank sensor codes to set. Replacement of the connector may take care of the issue.

• But if the crank sensor looks fine then other thing to be checked is burning of the fuel pump connector. A poor connection in between the pump connector and pump will result in the connector getting melt, which definitely will aggravate the poor connection. I've come across this cause intermittent driveability problems exactly like you are having, and won't set a code in the PCM since it's not monitored or controlled by the PCM. Replacement of the pump and connector together is usually necessary to repair this. The pump has an access panel under the left rear seat and you could check this fairly quickly.

• As per my vehicle repair experience its not the  PCM locking up. If the PCM was locking up somehow then it wouldn't restart the way it does. Usually when a module locks up it needs a power cycle (battery disconnect) to unlock, if it does unlock. If it's starting right back up I wouldn't suspect a PCM issue.And in your case the vehicle dies at idle but it will again restart normally and run.So PCM getting lock up is not possible.

These details will help.

Thanks.

Users Who Viewed This Problem Also Viewed:

Jeep Grand Cherokee will cut out, engine dies

http://technoanswers.blogspot.com/2012/11/jeep-grand-cherokee-will-cut-out-engine.html

1994 Toyota Pickup: Starts fine but dies in few seconds?

http://howtobyme.blogspot.in/2012/05/1994-toyota-pickup-starts-fine-but-dies.html

Ford Windstar battery dies in few days

http://technoanswers.blogspot.com/2012/10/ford-windstar-battery-dies-in-few-days.html

1994 Lexus ES300: Engine Idles Rough and Dies?

http://whatisbyme.blogspot.in/2012/05/1994-lexus-es300-engine-idles-rough-and.html

Car suddenly died and won’t start?

http://technoanswers.blogspot.in/2012/02/car-suddenly-died-and-wont-start.html

Car Clutch Makes Noise

Clutch Pedal Problem

WORN THROWOUT BEARING

Question:---

Vehicle drives fine but when Clutch Pedal is Pushed in the clutch makes noise.Its like Roaring and grinding Clutch Pedal Assembly.

But once the clutch pedal is released the noise stops.

What can cause these noise?

Please Help!!!

Answer by expert:--

Hello sir thanks for asking the question here.

At our Auto garage repair store we deal will many vehicles in the form of truck,van,jeep facing these kind of problem.

I will share the details and troubleshooting for this problem.

Like as you already said ,If the noise happens when pressing the clutch pedal and then goes away when clutch pedal is released then that's the issue with throwout bearing. 

Yes its worn throwout bearing.

Its the bearing on the clutch fork.

This bearing  moves forward toward the engine when pressing the clutch. The bearing pushes against the spring fingers on the clutch pressure plate when you press the pedal and this is what disengages the clutch. 

Since the only time the bearing spins and has a load on it is when you press the clutch pedal this is the only time it will make noise, and when you let off the pedal then it will stop pretty quickly. If the noise happens only when pressing the pedal and then goes away when you let off the pedal then it's going to have to be the throwout bearing.

I suggest you to get the throwout bearing inspected and replaced.

These will help.

Thanks.

Users Who Viewed This Problem Also Viewed:

How does Clutch works in car?

http://vwrepairhelp.blogspot.com/2011/11/how-does-clutch-works-in-car.html

Clutch pedal hard?

http://schematicsdiagram.blogspot.in/2012/02/clutch-pedal-hard.html

2001 Toyota Celica: Grinding noise when Clutch pedal is Pushed?

http://howtobyme.blogspot.in/2012/05/2001-toyota-celica-grinding-noise-when.html

Toyota Celica Noisy Clutch?

http://howtobyme.blogspot.in/2012/05/toyota-celica-noisy-clutch.html

No Clutch Pedal No pressure

http://whatisbyme.blogspot.in/2012/07/no-clutch-pedal-no-pressure.html

2006 Cadillac cts-v Clutch Getting stuck?

http://schematicsdiagram.blogspot.in/2012/04/2006-caddiliac-cts-v-clutch-getting.html

blinkers, stereo, and wipers will not work

Multiple problems noticed on 2000 Jeep Wrangler United States Manufactured Model.

CLUTCH GRINDING NOISE

QUESTION:----

While driving the vehicle noticed that blinkers, stereo and wipers not working.It will only work until turned the vehicle off and restarted it.

Including these problem suddenly other problem arise after that, It is the clutch grinding issue. The  clutch grinds when the clutch pedal is pushed in; But if the radio turns ON then there is no grinding clutch noise heard.

Is it some kind of short If not, then why the clutch would be affected by it?

More explanation about Grinding noise from the Customer who owns the Jeep Wrangler ..........


The Grind noise occurs when I turn the vehicle on; I already have the clutch pedal pushed in to start the jeep. Initially  while the start there is  very subtle grind noise heard but when the clutch  pedal is released it stops and again next time when clutch pedal is pushed in the loud grinding noise is heard .
But what i feel confusing is that this only happens when my radio and blinkers don't work.If While i start the vehicle and if radio and blinkers start then no such grinding noise is heard.

Please Explain me Why?



ANSWER BY EXPERT:---


Heelo customer.
Thanks for asking the problem.
I will like to share my Auto garage vehicle repair experience Suggestion with you.
As per what details you have provided, it sounds like the noise is appearing due to a failing throwout bearing.
The throwout bearing is the bearing that presses on the pressure plate to release the clutch when you press the pedal.
For your knowledge the clutch assembly system is a completely mechanical system where your other problem is electrical, and the systems are completely unrelated. Both the issues , one the radio and blinkers not working and other the clutch grind noise are two different issues.
I know it appears they problems are related and you can try repairing the electrical problem first, but it's highly unlikely that the problems are truly tied together.

Below i will explain your why these 2 issues are different problems and not related to each other:-----

The wipers, radio and turn signals not working is being caused by a bad ignition switch.It a very common problem and we at our auto garage deal with such problem regularly.
What has happened is the contacts in the switch are burnt and it's taking down a large power feed circuit. You would probably find if you moved the key forward and back a bit while it's acting up these items would come back on.
So getting the ignition switch checked and replaced if found to be faulty will help to solve the one problem.

In the same way getting the throwout bearing inspected and replaced will help to solve the other problem.

These will help.
Thanks.

Users Who Viewed This Problem Also Viewed:

How does Clutch works in car?

http://vwrepairhelp.blogspot.com/2011/11/how-does-clutch-works-in-car.html

Clutch pedal hard?

http://schematicsdiagram.blogspot.in/2012/02/clutch-pedal-hard.html

Toyota Celica Noisy Clutch?

http://howtobyme.blogspot.in/2012/05/toyota-celica-noisy-clutch.html

No Clutch Pedal No pressure

http://whatisbyme.blogspot.in/2012/07/no-clutch-pedal-no-pressure.html

2006 Cadillac cts-v Clutch Getting stuck?

http://schematicsdiagram.blogspot.in/2012/04/2006-caddiliac-cts-v-clutch-getting.html

Clutch squealing sound?

http://schematicsdiagram.blogspot.in/2012/04/clutch-squealing-sound.html

1995 Jeep Wrangler: Clutch Failed?

http://whatisbyme.blogspot.in/2012/06/1995-jeep-wrangler-clutch-failed.html

Chrysler Van System Too Lean Bank 1

OBD Error Code P0171 On Chrysler Van

Chrysler Van will not Start 

The starter turn over right but Engine will not start and Error code P0171 comes up.
n these case first see if you could hear the fuel pump turning ON when you crank/ start the engine.

Normally when you turn the key to start and start to Run you hear fuel pump running noise for 1-2 seconds.Hear that noise.If that fuel pump start noise is not heard then its fuel pump start up failure.

NOW why these code P0171 gets set:----


Engine running rich or Engine running Lean all is controlled by PCM.
The powertrain control module (PCM) has control and ability to watch the upstream oxygen sensors to know how rich or lean the engine is running. It has the ability to compensate for rich or lean conditions up to an extent. Suppose if the PCM detects Engine running lean, then in that condition it will start adding more and more fuel to try to bring it back to the correct range. It can add up to about 33% more fuel, and if it still can't bring the ratio back into the correct range then it will set this fault code. This could be a bad upstream oxygen sensor or MAP sensor, fuel quality issue, but in your case it was most likely caused by low fuel pressure.So first get the fuel pressure tested,these will help to confirm the problem.

As per our Auto garage repair experience ,With code P0171  set and you not hearing the pump run plus a no start condition is pointing to a likely fuel pump failure.
So first check fuel pressure,then check for power and ground at the pump connector while a helper cycles the key on and off or cranks the engine. If the pump does have power and ground but won't run then it will need to be replaced.If the pump has power but pressure is less then also pump is faulty.Also it can be faulty fuel pump relay,as power is not there.

The fuel pump relay is located in the box under the hood which you could try swapping with another and see if that helps but it's unlikely. Relays very seldom fail.

To measure the fuel pressure the simple procedure is as follows :--


Remove the fuel line from the rail and install a T hose inline and then attach the fuel pressure gauge to the T hose. There isn't a test port on the fuel rail itself on your Chrysler Van model.

Many a times confirming the fuel pump start up noise becomes very difficult.In that case take the help of helper.




As per Chrysler Van the pump connector is easily accessed, it clips up to the frame right behind the fuel tank located towards the center of the tank area.

With the chime going off when turning the key on it can be tough to hear the pump. It would be best to have a helper back near the tank or a helper turning the key while you listen back there.

For mode help and information regarding fuel pump connector ,There are four wires in the connector. The one to be checked are black/light green which is ground, and the fuel pump driver wire is dark blue/orange.

These details will help.
Thanks.

Users Who Viewed This Problem Also Viewed:

2000 Toyota Celica: Still Getting OBD code P0171? 

http://howtobyme.blogspot.in/2012/05/2000-toyota-celica-still-getting-obd.html

2003 Chrysler Town & Country: OBD Code P0171?

http://whatisbyme.blogspot.in/2012/06/2003-chrysler-town-country-obd-code.html

1999 Toyota Tacoma: Check Engine Light Read Code P0171?

http://whatisbyme.blogspot.in/2012/05/1999-toyota-tacoma-check-engine-light.html

What to Do When Car Turns Over But Won't Start?

http://technoanswers.blogspot.com/2012/11/what-to-do-when-car-turns-over-but-wont.html

 --------------

Car takes time to Crank and start?

http://howtobyme.blogspot.com/2011/12/car-takes-time-to-crank-and-start.html

------------

Car will not turn the ignition to start?

http://technoanswers.blogspot.com/2012/01/car-will-not-turn-ignition-to-start.html

-----------

Car starting issues?

http://technoanswers.blogspot.in/2012/02/car-starting-issues.html

------------

Car won't start without hitting the gas pedal?

http://schematicsdiagram.blogspot.com/2011/12/car-wont-start-without-hitting-gas.html

----------------

Car only starts when gas pedal is pressed?

http://technoanswers.blogspot.com/2012/01/car-only-starts-when-gas-pedal-is.html

----------

Car Starting Problems

http://whoisbyme.blogspot.in/2012/06/car-starting-problems.html

Jeep Wrangler Erratic Shifting

1999 Jeep Wrangler Under Full Throttle Jeep Shifts At 4k RPM

Throttle Shifts In and Out of Overdrive.

It can be issue with TPS also called as Throttle Position Sensor.


As per our Auto garage repair Experience I will share few troubleshooting tips regarding the cause and solution to this problem


As per what you mentioned I  expect more than 4,000 RPM at wide open throttle but not much more than that.

We at our Auto garage have noticed many such problems it's very much possible that low engine power is the issue. 
Another possibility is Low fuel pressure.
Low fuel pressure could cause it but that would usually come with spark knock on acceleration. 
But as you mentioned low engine power and erratic shifting with no error codes retrieved the most common cause of lack of engine power with no codes is a restricted catalytic converter due to internal breakup. 
To confirm the problem.
A backpressure test can be done to check the converters.


There are many other possibilities that can too cause these issues:-------
Like transmission related:-----
There are a couple things transmission related that could cause it too. 
As per your jeep brand and model/ year mentioned , it has primitive three speed trans with a mechanical governor in the tail housing. As per what i recollect these governors gave some trouble over the years with the governor valve sticking in the bore and causing shift issues.May be what exactly you are noticing, called low engine power and erratic shifting. It's very possible that the governor is stuck. To confirm whether governor pressure is issue.Governor pressure can be checked with a pressure gauge on the governor pressure tap on the trans.

As earlier mentioned it can be faulty throttle position sensor, but also It's possible that the throttle valve cable could be misadjusted too. 
To understand throttle cable working read the following:-----
The throttle valve cable goes from the trans to the throttle body.Now when you open the throttle it moves the throttle valve in the valve body and this has a huge influence on shift timing. If the cable was adjusted too long it would cause upshifts to be early.And may be these is what your problem.

As per your problem mentioned there is no one confirm solution to be pinpointed but there are few possibilities.Each can be possible.So looking at all possible issues will help you know what caused these issue on your jeep wrangler.


Like its mentioned before the erratic shifting is a common symptom of a governor issue or misadjusted throttle valve cable so those two things are where you're going to need to start. 

Like other possibilities, it can  be a leaking front clutch too, but definitely start by addressing these other things.

For  overdrive issue which you mentioned is actually torque converter lockup, it's a three speed transmission. Since you're having erratic idle and torque converter clutch operation at the same time it's extremely likely that the throttle position sensor issue. 
I suggest get the TPS inspected and replaced and see if same problem is there or its gone.
If you need to confirm the issue with TPS before getting New TPS, you can try these simple TPS test procedure.When it's idling erratic you can unplug the sensor, if the idle calms down then you know the TPS is the problem. 

At out garage we have also seen in some cases that problem was actually not TPS but it was  with TPS connector terminal grip, replacing the connector may take care of  problems. If you do replace the TPS  be sure to use a Mopar sensor to avoid future problems.It a good reputed brand of parts.


These details will help.
Thanks.

Users Who Viewed This Problem Also Viewed:

Gear indicator Shows "3" Instead Of "D"?

http://whoisbyme.blogspot.in/2012/07/gear-indicator-shows-3-instead-of-d.html

---------

2006 Chrysler 300c: Shifter Stuck in Park?

http://technoanswers.blogspot.in/2012/06/2006-chrysler-300c-shifter-stuck-in.html

----------

1998 Ford Expedition: Will not Shift Out of Park?

http://schematicsdiagram.blogspot.in/2012/06/1998-ford-expedition-will-not-shift-out.html

---------

Car will not move when in gear?                

http://repairhelpcenter.blogspot.in/2012/02/car-will-not-move-when-in-gear.html

-----------

Mercedes-Benz transmission sticks in first gear?

http://technoanswers.blogspot.com/2012/01/mercedes-benz-transmission-sticks-in.html

----------

Mercedes Benz not engaging in first gear?

http://technoanswers.blogspot.com/2012/01/mercedes-benz-not-engaging-in-first.html

----------

Chrysler PT Cruiser only goes in First gear?

http://howtobyme.blogspot.com/2011/11/chrysler-pt-cruiser-only-goes-in-first.html

                           

----------