Power steering and water pump pulley location on Saturn?

The exact pulley location is required while routing the drive belt.

Below is the exact drive belt pulley location shown for Saturn l series.


See the diagram shown below :----


This will help.
Thanks.

See below related help solutions :----

Drive belt routing diagram for Saturn L100?

http://technoanswers.blogspot.in/2012/02/drive-belt-routing-diagram-for-saturn.html

Front side of drive belt routing for Saturn L100?

http://technoanswers.blogspot.in/2012/02/front-side-of-drive-belt-routing-for.html

Belt tensioner location diagram for Saturn L100?

http://technoanswers.blogspot.in/2012/02/belt-tensioner-location-diagram-for.html

Saturn drive belt tensioner diagram?

http://technoanswers.blogspot.in/2012/02/saturn-drive-belt-tensioner-diagram.html

Power steering pulley location on Saturn L series drive belt?

http://technoanswers.blogspot.in/2012/02/power-steering-pulley-location-on.html

With AC and without AC drive belt routing diagram for Saturn?

http://technoanswers.blogspot.in/2012/02/with-ac-and-without-ac-drive-belt.html

How test cam shaft? Testing Car Camshaft?

http://repairhelpcenter.blogspot.in/2012/02/how-test-cam-shafttesting-car-camshaft.html

Acceleration lag problem?

http://repairhelpcenter.blogspot.com/2012/01/acceleration-lag-problem.html

How to repair FICM on 2005 Ford f350?

http://schematicsdiagram.blogspot.in/2012/02/how-to-repair-ficm-on-2005-ford-f350.html

Where is glow plug module located on 2005 Ford f350?

http://technoanswers.blogspot.in/2012/02/where-is-glow-plug-module-located-on.html

How to Replace rear quarter glass on Toyota Tacoma?

http://repairhelpcenter.blogspot.com/2012/01/how-to-replace-rear-quarter-glass-on.html

Overdrive light in the dash blinks?

http://repairhelpcenter.blogspot.com/2012/01/overdrive-light-in-dash-blinks.html

Front Suspension diagrams?

http://howtobyme.blogspot.in/2012/02/front-suspension-diagrams.html

No pulse to injectors?

http://technoanswers.blogspot.com/2012/01/no-pulse-to-injectors.html

How to bypass immobiliser on Rover 200?

http://technoanswers.blogspot.com/2012/01/how-to-bypass-immobiliser-on-rover-200.html

Service engine soon light is ON?

http://technoanswers.blogspot.in/2012/02/service-engine-soon-light-is-on.html

Engine misses and truck jumps? Hard to down shift? Issue with high gear only?

http://technoanswers.blogspot.in/2012/02/engine-miss-and-truck-jumps-hard-to.html

Radio Power Antenna wiring diagram for 1992 Lincoln Town Car?

http://technoanswers.blogspot.in/2012/02/radio-power-antenna-wiring-diagram-for.html

Where is Water Pump located on Toyota Corolla?

The water pump is usually located on the front of the engine and driven by one of the accessory drive belts, that circulates the coolant by causing it to move from the lower radiator-outlet section into the engine by centrifugal action of a finned impeller on the pump shaft.

To replace water pump,the timing belt has to be removed.
If you notice car overheats and also makes loud sound/noise.Then yes water pump has to be inspected.
If the bearings in the waterpump were failing, it could be loud.The water pump is mounted behind the timing belt. The Timing belt has to be removed before the water pump.However,to conform if water pump is faulty or not. You can grab the waterpump pulley and wiggle it. If it has any play, it is bad, if it does not, then it is not your problem.

In that case Thermostat can be the cause of overheating.If you need details for thermostat replacement,check the link below :---

http://technoanswers.blogspot.com/2011/12/thermostat-replacement-on-toyota.html

But if water pump pulley is making noise when you wiggle and it has play,then water pump is the cause of problem.See the water pump location diagram below.This will give you better idea of where to look for water pump on your Toyota corolla.

There is one more procedure,where you dont have to remove timing belt to remove water pump,but that procedure is very conjested and with very less room.You cannot remove water pump very freely.
In that You actually  slip the pump out without actually removing the timing belt, but the engine mount and timing covers have to be removed.

This basic details will help.Thanks.

------------------

If you need dis-assembly or replacement instructions for any other auto/car part, or you want to ask question related to your car/truck jeep problem then please leave the comment with your details, so I can provide you the required instructions and solutions.

Also see this for more help:----

Water pump replacing procedure for all vehicles?

http://technoanswers.blogspot.com/2011/11/water-pump-replacing-procedure-for-all.html

How to Replace a Water Pump

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-water-pump.html

How to route Water Pump Belt for 1992 Oldsmobile Cutlass Ciera?

http://carbeltrouting.blogspot.com/2011/12/how-to-route-water-pump-belt-for-1992.html

How to replace Water Pump on Acura Car models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-water-pump-on-acura-car.html

How to Remove Water Pump on Toyota Previa?

http://technoanswers.blogspot.com/2011/12/how-to-remove-water-pump-on-toyota.html

Replacing timing belt cover on 1992 Volvo 940 ?

Timing Belt Cover

REMOVAL & INSTALLATION

2.3L 4-Cylinder Engine

1. Disconnect the negative battery cable.
2. Remove the cooling fan and shroud.
3. Remove the drive belts.
4. Remove the water pump pulley.
5. Remove the 4 retaining bolts and lift off the timing belt cover.

To install:

6. Clean all gasket mating surfaces thoroughly.
7. Install the timing belt cover using a new gasket.
8. Install the water pump pulley, and all drive belts.
9. Install the fan and shroud.
10. Connect the negative battery cable.
11. Start the engine and check for leaks.

B234F 4-Cylinder Engine

See Figure 1

1. Remove the negative battery cable.
2. Remove the drive belts.
3. Remove the radiator fan, its pulley and the fan shroud.
4. Remove the drive belts for the power steering belts and the air conditioning compressor.
5. Beginning with the top cover, remove the retaining bolts and remove the timing belt covers.

To install:

6. Clean all gasket mating surfaces thoroughly.
7. Install the timing belt covers using new gaskets.
8. Install the water pump pulley, and all drive belts.
9. Install the fan and shroud.
10. Connect the negative battery cable.
11. Start the engine and check for leaks.

Fig. Fig. 1: The B234F engine has a three-piece timing cover

2.9L 6-Cylinder Engine

1. Disconnect the negative battery lead.
2. Remove the drive belt.
3. Remove the lower timing belt cover, splash guard and vibration damper guard.
4. Remove the ignition coil cover.
5. Remove the upper timing cover.

To install:

6. Install the upper timing belt cover.
7. Install the ignition coil cover.
8. Install the lower timing belt cover, splash guard and vibration damper guard.
9. Install the drive belt.
10. Connect the negative battery cable.

2.3L and 2.4L 5-Cylinder Engines

See Figures 2, 3, 4, 5, 6, 7, 8 and 9

1. Disconnect the negative battery cable.
2. Remove the coolant expansion tank and place it on top of the engine.
3. Remove the spark plug cover.
4. Remove the drive belts.
5. Remove the fuel line clips.
6. Remove the right front wheel and loosen the inner fenderwell.
7. Remove the vibration damper guard and turn crankshaft pulley until the marks are lined up.
8. Remove the water pump pulley.
9. Remove the retaining bolts and lift off the timing belt cover.

To install:

10. Position the timing belt cover in place and secure with the retainer bolts.
11. Install the water pump pulley, followed by the drive belts.
12. Install the remaining components.
13. Connect the negative battery cable.

Fig. Fig. 2: Unplug the connector, disconnect the hose and remove the expansion tank

Fig. Fig. 3: Remove the belt and the tensioner

Fig. Fig. 4: Remove the spark plug cover to ...

Fig. Fig. 5: ... access the fuel line clips

Fig. Fig. 6: Unfasten the retaining bolts and remove the fuel line clips

Fig. Fig. 7: Remove the fenderwell trim

Fig. Fig. 8: Remove the water pump pulley; it is retained by a shoulder bolt (shown)

Fig. Fig. 9: Remove the retaining bolts and carefully remove the timing belt cover

-----------------

For more car related problem troubleshooting:---

This are the sections, you can go through and click the link to read its troubleshooting.

---------

The car will not start?

http://schematicsdiagram.blogspot.com/2011/06/car-will-not-start.html

-----------------

Car will not crank?

http://schematicsdiagram.blogspot.com/2011/06/car-will-not-crank.html

-----------

Car has no spark?

http://schematicsdiagram.blogspot.com/2011/06/car-has-no-spark.html

-------------

How to troubleshoot car battery?

http://schematicsdiagram.blogspot.com/2011/06/how-to-troubleshoot-car-battery.html

-----------------

How to test starter solenoid?

http://schematicsdiagram.blogspot.com/2011/06/how-to-test-starter-solenoid.html

--------------------

How to test cars starter?

http://schematicsdiagram.blogspot.com/2011/06/how-to-test-cars-starter.html

How to replace starter in car?

http://schematicsdiagram.blogspot.com/2011/06/how-to-replace-starter-in-car.html

-----------

car will turn over but will not start?

http://technoanswers.blogspot.com/2011/05/car-will-turn-over-but-will-not-start.html

-----------------

Car wont start?

http://howtobyme.blogspot.com/2011/10/car-wont-start.html