2010 Jeep Wrangler:Front Wheels Bounce and Vehicle Out Of Control

Front wheels vibrate violently While Driving Above 50 KMPH

Its a front end collision rebuilt vehicle,bought from salvage yard with a salvage yard certificate.

There are few possibilities for this problem to arise:

1) Get complete inspection  done of any steering components that aren't new. Like any loose tie rod end, ball joint, track bar or control arm bushing will contribute to this.

2) Next get the alignment checked. If caster is too far positive it will cause this. Since it's been in a front end collision this could be an issue

3) If all the basics checked out ok. Then, the main cause of this is a weak steering damper, which mounts between the right axle tube and right drag link. 

WHAT EXACTLY STEERING DAMPER DO?

It's job is to absorb road input to the steering to prevent the exact problem you are having. The original dampers on these were very small, especially if there is a lift or over sized tires on the vehicle. If you still have problems after checking alignment and replacing any loose front end parts then I would recommend replacing the steering damper with a heavy duty aftermarket one.Please don't go for low quality cheap auto parts.They don't give required performance and don't last long.

Hope these will help.

Thanks.

Brake drag from wheel area while driving?

http://schematicsdiagram.blogspot.in/2012/02/brake-drag-from-wheel-area-while.html

2001 Toyota Camry: Wheel Wobble While Braking?

http://whatisbyme.blogspot.in/2012/05/2001-toyota-camry-wheel-wobble-while.html

Car shakes like the wheels are going to fall off

http://technoanswers.blogspot.com/2012/11/car-shakes-like-wheels-are-going-to.html

1993 Toyota Corolla: Steering Wheel Vibrates at Idle?

http://whatisbyme.blogspot.in/2012/05/1993-toyota-corolla-steering-wheel.html

How to Remove Steering Wheel on Volkswagen Touran?

http://www.howtobyme.blogspot.com/2012/07/how-to-remove-steering-wheel-on.html

2003 Toyota Camry: Groaning Sound coming from Steering wheel?

http://whatisbyme.blogspot.in/2012/05/2003-toyota-camry-groaning-sound-coming.html

Yamaha Jet Ski Boat Steering is Stiff?

Stiff Hard Steering On Boat

FOR YAMAHA JET SKI MANUAL

Yamaha  SX230 Steering is very Stiff?

In this case the Steering cable needs to be inspected.If they are dried out then has to be disconnected and lubed.

Steering cables do not have any points that you can grease them that will save them. You can only lubricate the exposed ends. 

Also another option is removing throttle assembly.

The throttle control assembly is actually really easy to remove to lube the cables and adjust the tension on the levers if need be.

If the cables are worn out,then replacing it is the only option.

First try disconnect and check that the steering head is free , if so then it is definitely the cables which can be inspected.If faulty replace,if dried out then should be fitted with grease nipple access points.

This details will help.

Thanks.

Users Who Viewed This Problem Also Viewed:

How to remove Flywheel on Jet ski?

http://www.howtorepairguide.com/2012/07/how-to-remove-flywheel-on-jet-ski.html

Jetski Sputters and Low RPM?

http://whatisbyme.blogspot.in/2012/07/jetski-sputters-and-low-rpm.html

Jet Ski Not Starting?

http://whatisbyme.blogspot.in/2012/07/jet-ski-not-starting.html

How to Remove steering wheel on Chevrolet Malibu?

Its not very hard with diagrams and detailed procedure.
See the details mentioned below :----------

Removal & Installation

1. Disable the Supplemental Inflatable Restraint (SIR) system, as outlined in the link below. 
   
   
   http://technoanswers.blogspot.com/2011/12/how-to-disarming-air-bag-system.html
   

   Fig. Disconnect the electrical connectors (4) from the column
2. Remove the steering column trim covers.
3. Remove the inflator module.
4. Remove the steering wheel nut.
   
   NOTE

   When removing the steering wheel, use only the specified steering wheel puller. Do not hammer on the end of the steering column shaft. Hammering could loosen the plastic injections which maintain the steering column rigidity.
   
   
   
   
   

   

   Fig. Remove the steering wheel using the special tool J1859-A and the special tool J42120
5. Remove the steering wheel using the special tool J1859-A and the special tool J42120.
6. Disconnect the electrical connectors from the column.
7. Route the electrical connectors through the steering wheel opening.
8. Remove the steering wheel from the vehicle.

To install:

1. Route the electrical connectors through the steering wheel opening.
2. Connect the electrical connector to the steering column.
3. Install the steering wheel on the steering column.
   
   NOTE

   Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems. Install the steering wheel nut on the steering column, and tighten the nut to 27 ft. lbs. (37 Nm).
4. Install the inflator module.
5. Install the steering column trim covers.
6. Enable the SIR system.

1. Remove the upper steering column trim cover.
2. Disable the Supplemental Inflatable Restraint (SIR) system, as outlined in the Chassis Electrical Section.
3. Remove the inflator module .
   
   
   

   

   Fig. Disconnect the steering wheel control electrical connector
4. Disconnect the steering wheel control electrical connector.
   
   
   

   

   Fig. Remove the steering wheel nut
5. Remove the steering wheel nut.
6. Install special tool J42578 and special tool J1859-A to the steering wheel.
   
   
   

   

   Fig. Use special tool J42578 and special tool J1859-A in order to remove the steering wheel
7. Use special tool J42578 and special tool J1859-A in order to remove the steering wheel.
8. Remove special tool J42578 and special tool J1859-A from the steering wheel.
9. Remove the controls and the control harness from the steering wheel.

To install:

1. Install the controls and the control harness to the steering wheel.
2. Route the steering column wiring through the steering wheel.
3. Install the steering wheel.
4. Connect the steering wheel control electrical connector.
5. Install the steering wheel nut, and tighten the nut to 24 ft. lbs. (32 Nm).
6. Install the inflator module.
7. Install the upper steering column trim cover.
8. Enable the SIR system.

1. Before servicing the vehicle, refer to the Precautions Section.
2. Disable the Supplemental Inflatable Restraint (SIR) system, as outlined in the Chassis Electrical Section.
3. Remove the upper steering column trim cover.
4. Remove the inflator module .
   
   
   

   

   Fig. Disconnect the steering wheel control electrical connector
5. Disconnect the steering wheel control electrical connector.
   
   
   

   

   Fig. Remove the steering wheel nut
6. Remove the steering wheel nut.
7. Install special tool J42578 and special tool J1859-A to the steering wheel.
   
   
   

   

   Fig. Use special tool J42578 and special tool J1859-A in order to remove the steering wheel
8. Use special tool J42578 and special tool J1859-A in order to remove the steering wheel.
9. Remove special tool J42578 and special tool J1859-A from the steering wheel.
10. Remove the controls and the control harness from the steering wheel.

To install:

1. Install the controls and the control harness to the steering wheel.
2. Route the steering column wiring through the steering wheel.
3. Install the steering wheel.
4. Connect the steering wheel control electrical connector.
5. Install the steering wheel nut, and tighten the nut to 24 ft. lbs. (32 Nm).
6. Install the inflator module.
7. Install the upper steering column trim cover.
8. Enable the SIR system.

---------------

This basic details will help.Thanks.

------------------

If you need dis-assembly or replacement instructions for any other auto/car part, or you want to ask question related to your car/truck jeep problem then please leave the comment with your details, so I can provide you the required instructions and solutions.

For more steering wheel and other car solution help, check the list shown below:---------

Steering Wheel Locked?

http://schematicsdiagram.blogspot.com/2011/12/steering-wheel-locked.html

How to replace Power Rack and Pinion Steering Gear on Acura Car Models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-power-rack-and-pinion.html

How to replace Power Steering Pump on Acura Car Models?

Also bleeding:

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-power-steering-pump-on.html

How to replace Steering Linkage on Acura Car Models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-steering-linkage-on.html

How to replace Steering Wheel on Acura Car Models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-steering-wheel-on-acura.html

How to replace Power Steering Pump on 1999 Acura TL?

http://howtobyme.blogspot.com/2011/11/how-to-replace-power-steering-pump-on.html

How to Disarming the Air Bag System?

http://technoanswers.blogspot.com/2011/12/how-to-disarming-air-bag-system.html