@

Showing posts with label How to replace blower motor. Show all posts
Showing posts with label How to replace blower motor. Show all posts

Saturday, February 18, 2012

How to replace blower motor on 1990 Honda Accord?

Blower motor is replaced,when you notice no heat or cold problem for car heater/ac unit.The blower motor fan will not operate when motor is faulty.

The procedure to replace blower motor on 1990 Honda accord model is as follows :----


  1. With A/C:
    • Remove the A/C band and remove the blower under cover. Remove the blower assembly
NOTE: Be careful not to break the tabs while removing the blower under cover.

BLOWER MOTOR REPLACEMENT 
Refer to illustration for blower unit disassembly and reassembly, noting the following:
  • Before reassembly, make sure that the air door and linkage moves smoothly without binding.
  • When reattaching the recirculation control motor, make sure its positioning will not allow the air door to be pulled too far. Attach the recirculation control motor and all linkage, then apply battery voltage and watch the recirculation control door movement. If necessary, loosen the holding screw and move the recirculation control motor up or down.
graphicCONTROL ROD ADJUSTMENT
Connect the recirculation control motor connector to the main wire harness and turn the FRE/REC switch to "REC". Hold the air door closed, then connect the control rod to the clip on the arm.


BLOWER UNIT REMOVAL
graphic
graphic


  1. Remove the glove box.
  2. Remove the glove box frame.
  3. Without A/C:
    graphic

    • Remove the self-tapping screws and remove the heater duct.
  4. Without A/C:
    • Remove the blower unit mounting nuts .
    • Disconnect the connectors from the blower motor, resistor and recirculation control motor, then remove the blower assemblygraphic
  5. This will help.
  6. Thanks.

See below related help solutions for more help :-----


Heater/AC blower motor not working on 1995 Isuzu Trooper?

http://technoanswers.blogspot.in/2012/02/heaterac-blower-motor-not-working-on.html


Replace blower motor?

http://repairhelpcenter.blogspot.com/2012/01/replace-blower-motor.html

How to replace blower motor fan assembly on 2000 GMC Yukon?

http://repairhelpcenter.blogspot.com/2012/01/how-to-replace-blower-motor-fan.html

Audi A4 blower motor blows Warm Air?

http://howtobyme.blogspot.com/2011/12/audi-a4-blower-motor-blows-warm-air.html

Heater stuck on defrost?

http://howtobyme.blogspot.com/2011/12/heater-stuck-on-defrost.html

Where is Blower motor resistor located on 2006 Ford F 250?

http://schematicsdiagram.blogspot.com/2011/12/where-is-blower-motor-resistor-located.html

Dodge Caravan AC Heater Control only works on high mode?

http://schematicsdiagram.blogspot.com/2011/12/dodge-caravan-ac-heater-control-only.html

Honda Civic Blower Motor Only works on high mode?

http://schematicsdiagram.blogspot.com/2011/12/honda-civic-blower-motor-only-works-on.html

How to Test and Replace Blower motor on car?

http://repairhelpcenter.blogspot.com/2011/12/how-to-test-and-replace-blower-motor-on.html

How to Replace Blower Motor Wheel?

http://repairhelpcenter.blogspot.com/2011/12/how-to-replace-blower-motor-wheel.html

How to Replace Blower Motor on 2008 Honda Odyssey?

http://howtobyme.blogspot.com/2011/12/how-to-replace-blower-motor-on-2008.html

Where is blower motor relay located on 2005 Ford F-350?

http://technoanswers.blogspot.in/2012/02/where-is-blower-motor-relay-located-on.html






Wednesday, October 19, 2011

How to replace blower motor on Chevrolet Tracker?

Blower motor removal for 1998 Chevrolet Tracker.
The instructions are as follows :--


Blower Motor


Sidekick, Tracker, Sidekick Sport and X-90 Models
See Figures 3 and 4
  1. Disconnect the negative battery cable.
  2. On models with air bags, disable the system.
  3. Remove the glove box assembly by opening it, and loosening the pivot and retaining screws from inside the glove box with a screwdriver.


Click image to see an enlarged view
Fig. Fig.3: Exploded view of the blower motor mounting in the heater case
  1. On 1996-98 models, remove the instrument panel assist holder (lower brace).
  2. Remove the relays and relay bracket from the blower motor case.
  3. Disengage the blower motor and resistor wire connectors.
  4. Disconnect the fresh air control cable from the blower motor case.
  5. Remove the 3 blower motor mounting screws.
  6. Remove the blower motor.


Click image to see an enlarged view
Fig. Fig. 4: To remove the blower motor, open the glove box and loosen the box pivot and retaining screws ...


Click image to see an enlarged view
Fig. Fig. 5: ... then remove the glove box from the instrument panel


Click image to see an enlarged view
Fig. Fig. 6: From beneath the instrument panel, detach the wiring harness connectors ...


Click image to see an enlarged view
Fig. Fig. 7: ... and hoses from the blower motor


Click image to see an enlarged view
Fig. Fig. 8: Blower motor mounting bolt locations on the bottom of the heater case


Click image to see an enlarged view
Fig. Fig. 9: Loosen all of the blower motor-to-heater case assembly mounting bolts ...


Click image to see an enlarged view
Fig. Fig. 10: ... then lower the blower motor out of the heater case assembly
To install:
  1. Install the blower motor and secure with the 3 screws.
  2. Connect the fresh air control cable to the blower motor case.
  3. Connect the electrical connectors and install the glove box assembly.
  4. Install the relay bracket and relays on the blower motor case.
  5. On 1996-98 models, install the instrument panel assist holder.
  6. Connect the negative battery cable.
  7. If applicable, enable the air bag system.
  8. Check for proper blower motor operation.

----------------
If you want to know

How to replace Heater core on Chevrolet Tracker?

Click the link below:---

--------------
If you want to know

How to replace Control Panel on Chevrolet Tracker?

Click this link below:---
---------



@